manualshive.com logo in svg

Sofarsolar HYD 10KTL-3PH, Installation And Operating Manual, Page: 22 / 128

Share
Download
Sofarsolar HYD 10KTL-3PH Installation And Operating Manual Download Page 22

PRODUCT FEATURES 

 

22

 

HYD 5K...20KTL-3PH

 

3.5.5

 

System with multiple inverters (5

–

200 kW) 

Up to 10 inverters can be connected in parallel, to the grid and EPS 

connections, resulting in an EPS output of up to 200 kVA.

 

 

 

NOTE 

•

 

The inverters connected in parallel should have the same 

power and battery configuration. 

•

 

The energy meter or CTs are connected to the Master 

inverter. Control of all inverters takes place via the link 

cable. 

•

 

For the parallel switching of several devices, it is 

recommended to use a joint AC load break switch for the 

connected loads at the LOAD connection.

 

•

 

For the parallel switching of several devices, it is 

recommended to use a joint AC load break switch for the 

connected loads at the GRID connection. 

AMASS-

Storage 
Battery

Normal Load

WiFi/GPRS

，

RS485,USB,CAN2.0

Grid

Critical Load

Power Generation Date 

Monitoring Platform

AMASS-

Storage 
Battery

Up to 10*Inverters Parallel 

Connection

Hydbrid Inverter    

Primary

   Hydbrid Inverter  

Replica

PV panels

PV panels

Smart Meter

Summary of Contents for HYD 10KTL-3PH

































































































































Reviews:

No comments