Sofarsolar HYD 10KTL-3PH Installation And Operating Manual Download Page 104

Page: 104 / 128

OPERATION OF THE DEVICE

104

HYD 5K...20KTL-3PH

Parallel Master/Slave

One Inverter need to be set as

Master (Primary), all other inverters

need to be set to Slave (Replica)

Parallel Address

Set each inverter with an individual

parallel address. (It is an

independent number from Modbus

ID)

Save

After changes, select “save” item to

save the settings

8. Bluetooth Reset

Resets the Bluetooth interface of

the inverter

9. CT Calibration

This function is used to correct the

direction and grid phase

assignment of the connected CTs.

During CT Calibration, the inverter

must be connected to a battery and

the grid.

It is recommended to turn off the

load during calibration.

If calibration fails, check if the

battery can be charged/discharged

correctly

10. Switch On / Off

The inverter can be switched on,

switched off, set to standby or set

to normal operating mode, which

can be useful for installation or

maintenance work

11. Unbalanced Support

Default setting: disabled

Summary of Contents for HYD 10KTL-3PH

































































































































Search results

Summary of Contents for HYD 10KTL-3PH

Reviews:

Sofarsolar HYD 10KTL-3PH, Installation And Operating Manual, Page: 104 / 128

Search results

Summary of Contents for HYD 10KTL-3PH

Reviews: