Sofarsolar HYD 10KTL-3PH Installation And Operating Manual Download Page 106

Page: 106 / 128

OPERATION OF THE DEVICE

106

HYD 5K...20KTL-3PH

Inverter Info (1)

Serial number, software versions

Inverter Info (2)

Hardware version, Power, Country Code

Inverter Info (3)

Input Channel 1 … 4

Inverter Info (4)

Energy Storage Mode, RS485 Address, EPS

Mode, IV Curve

Inverter Info (5)

Logic Interface, Grid code settings

Inverter Info (6)

Anti-reflux, Isolation resistance

2. Battery Info

Battery 1/2 Info (1)

Battery

Type,

Capacity,

Overvoltage

Protection, Depth of Discharge (DOD)

Battery 1/2 Info (2)

Max. charging / discharging current and

voltage

Battery 1/2 Info (3)

Low voltage protection, nominal battery

voltage

1. Safety Parameters

Safety Parameters (1) Over- / under-voltage protection

Safety Parameters (2) Over- / under-frequency protection

Safety Parameters (3) 10 Min. overvoltage protection

Event List menu

The event list is used to display the real time event recordings,

including the total number of events and each specific ID no. and

event time. The most recent events are listed at the top.

2. Event list

Current event

Show latest event

Event History

Show event history

Summary of Contents for HYD 10KTL-3PH

































































































































Search results

Summary of Contents for HYD 10KTL-3PH

Reviews:

Sofarsolar HYD 10KTL-3PH, Installation And Operating Manual, Page: 106 / 128

Search results

Summary of Contents for HYD 10KTL-3PH

Reviews: