Sofarsolar HYD 10KTL-3PH Installation And Operating Manual Download Page 122

Page: 122 / 128

TROUBLESHOOTING HANDLING

122

HYD 5K...20KTL-3PH

ID157

BMSCommunicatonFault

(BMS 2)

Lithium battery

communication

error

Make sure your battery is

compatible with the

inverter.

CAN communication is

recommended. Check the

communication line or the

connection of the battery

and the inverter for errors.

ID161

ForceShutdown

Forced shutdown

The inverter has been

forcibly disconnected.

ID162

RemoteShutdown

Remote shutdown

The inverter is shut down

remotely.

ID163

Drms0Shutdown

DRM 0 shutdown

The inverter is running

with a Drms0 shutdown.

ID165

RemoteDerating

The inverter has

reduced its power

due to remote

control

This message is for

information and is not an

error

ID166

LogicInterfaceDerating

The inverter has

reduced its power

due to the digital

inputs

ID167

AlarmAntiRefluxing

Power reduction

due to current

sensor or

SmartMeter

configuration

ID169

FanFault1

Fan 1 fault

Check if the

corresponding fan of the

inverter is running

normally.

ID170

FanFault2

Fan 2 fault

ID171

FanFault3

Fan 3 fault

ID172

FanFault4

Fan 4 fault

Summary of Contents for HYD 10KTL-3PH

































































































































Search results

Summary of Contents for HYD 10KTL-3PH

Reviews:

Sofarsolar HYD 10KTL-3PH, Installation And Operating Manual, Page: 122 / 128

Search results

Summary of Contents for HYD 10KTL-3PH

Reviews: