socomec Masterys MAS2BC115M+D1 Installation And Operating Manual Download | Manualshive

Page: 35 / 48

background image

MASTERYS BC

from 15 to 20 kVA

5

ENGLISH

8

COMMUNICATION

T.SERVICE This is a cutting edge supervision service ensuring 24 x 7 service.
It ensures effective prevention and constant monitoring of the system.
Communication  between  the  UPS  and  the  local  technical  support  centre
is via Internet with the help of NetVision (via the mail-server on the same
network).
Any emergency situation is managed and resolved extremely quickly and
remotely  by  the  Support  Centre,  with  immediate  intervention  on  site  if
needed.
The  auto-diagnostic  system  analyses  UPS  operating  conditions,  identifies
faults  and  monitors  environmental  conditions  such  as  temperature,  over-
load, etc, avoiding the risk of equipment stoppages. In the event of a failure,
the system immediately sends a diagnostic report via e-mail or modem to
the support centre.

«
...
33
34
35
36
37
...
»

Summary of Contents for Masterys MAS2BC115M+D1

















































Reviews:

No comments

Related manuals for Masterys MAS2BC115M+D1

Brand: G-Tec Pages: 50

Brand: Staco Energy Pages: 47

Brand: HP Pages: 11

Brand: HP Pages: 5

Brand: HP Pages: 12

Brand: HP Pages: 11

J4367A - UPS R3000 XR

Brand: HP Pages: 65

Brand: HP Pages: 115

Brand: HP Pages: 120

Brand: HP Pages: 2

Minuteman PRO-RT 2U Series

Brand: Para systems Pages: 18

Brand: Falcon Pages: 42

OPTIMA-T09W-06K-230V

Brand: Xmart Pages: 36

Brand: Xtreme Pages: 49

Brand: Controlled power company Pages: 57

Brand: Eaton Pages: 110

Brand: Eaton Pages: 29

Brand: Unitek Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands