socomec MASTERYS GP4 Series Installation And Operating Manual Download Page 30

Page: 30 / 72

MASTERYS GP4 60-160 kVA - Ref.: IOMMASGPXX07-EN 05

Connection example - single unit

UPS

BATTERY

CABINET

BATTERY

CABINET

Connection example - parallel configuration with shared battery

UPS

BATTERY

CABINET

BATTERY

CABINET

BATTERY

CABINET

Connection example - parallel configuration with distributed battery

UPS

BATTERY

CABINET

BATTERY

CABINET

BATTERY

CABINET

Note!
When battery cabinets not supplied by Socomec are used, the installer is responsible for:

- checking electrical compatibility;

- checking the presence of appropriate protective devices (fuses and circuit breakers that ensure the

cables are protected from the UPS to the battery cabinet).

Once the UPS is switched on – before closing the battery switches – check the battery param-
eters on the control panel menu. For further information, refer to 'Display operation' chapter.

Note!
Not all battery/capacity combinations are available.

Summary of Contents for MASTERYS GP4 Series









































































Search results

Summary of Contents for MASTERYS GP4 Series

Reviews:

Related manuals for MASTERYS GP4 Series

Brands by name

Popular brands

socomec MASTERYS GP4 Series, Installation And Operating Manual

Search results

Summary of Contents for MASTERYS GP4 Series

Reviews:

Related manuals for MASTERYS GP4 Series

Brands by name

Popular brands