background image

 

DISPLAYS & CONTROL

 

Q

   

SECTION 1   

 

12 

 

5.1.2  Battery-powered operation (in cases of black-out) 

 

 
 

 

 

Following a failure of the mains power supply or a 
condition of mains out of the accepted limits, the UPS 
goes immediately into battery-powered operation without 
disturbance of the power supply to the application.  
An acoustic and a visual signal show the battery 
operation status. 

 

 

The acoustic alarm may be muted temporarily by 

pressing the “ON” button for 3 sec.  

 
Your application 

REMAINS 

powered 

 

 
 
 

 

 

 
In the event of a prolonged mains failure, when battery 
back-up will soon run out, the imminent shutdown is 
clearly signalled: “battery low” condition. 
The battery LED bar is almost out, the buzzer sounds 
again automatically at a more frequent rate (and can no 
longer be muted). 

It is recommended to close down applications manually if 

the automatic shutdown procedure has not been 
activated via the specific software installed on the 
computer. 

 

WARNING! your application 

REMAINS

 powered but 

residual operation time is nearly out!

 

 

 

 

 

When the regular mains power supply returns, normal 

operation is restored automatically. 

 
Your application 

IS

 powered by the UPS with continuous 

power ensured and the battery is recharged automatically.

 

 
 
 

 

 

 
If the black-out is not reset, the UPS provides power to 

the application until the batteries are completely 
discharged or until shutdown is activated through the 
software. 

The output is thus disconnected while awaiting the return 

of the mains. 

When the mains is restored, the UPS will start again 

automatically. 

L

 

WARNING

 

A few hours are needed to guarantee recharging of the 

batteries and return them to fully operative conditions

.

 

 
Your application is NOT powered. 

 

Summary of Contents for ENT-RK10






















Reviews: