background image

1. Introduction

1 - 1

!

!

Indicates a potentially hazardous situation which, if not avoided, could 

result in severe injury or death.

W A R N I N G

1. Introduction

1.1 INTRODUCTION

PURPOSE & LIMITATIONS

This Service & Parts Manual is designed to provide instructions and illustrations for the 

safe operation and maintenance of the MB20J & MB26J Work Platform manufactured 

by Snorkel. The purpose of this machine is to provide fast and safe access to difficult to 

reach areas. The machine may only safely operated on firm level ground. Refer to the 

Specification section for the machines access limitations.

DO NOT

 use on soft ground or on slopes greater than 2 degrees.

DO NOT

 use the lifting mechanism to raise or lower goods or persons except within the 

cage and subject to the weight limitations.

DO NOT

 enter the platform from a structure, rack or other platform.

ENVIRONMENTAL TEMPERATURE LIMITATION

, The machine is primarily for use in 

normal ambient temperatures and conditions ranging between 50c to -20c.

SCOPE

This manual includes the procedures and responsibilities for the inspection, transportation, 

safe operation, maintenance, and repair of this product. The Maintenance Section within 

the Parts & Service Manual also covers preventative maintenance and troubleshooting. 

SPECIAL INFORMATION

Throughout this manual the users attention is drawn to these special warning boxes:

1.2 GENERAL DESCRIPTION

The MB20/26J are self propelled, fast acting aerial work platforms, designed to raise two 

operators with hand tools to a platform floor height of 6.00 m and 7.76 m respectively. The 

accessible height is approximately 2.00 m above these figures. It is designed to travel with 

safe working load and work tools up to an upper limit,  See table on page 2-18 / 2-19.
The unit offers the ability to reach over obstacles but must be used on firm and level ground 

at all times.

Indicates an imminently hazardous situation which, if not avoided, will 

result in severe injury or death.

!

!

D A N G E R

!

!

Indicates a potentially hazardous sit uation which, if not avoided, may 

result in minor or moderate injury.

C A U T I O N

Summary of Contents for MB20J

































Reviews: