background image

2. 

Operation & Specifications

2 - 14

TRANSPORT BY TRUCK

The MB20/26J can be carried on a suitably rated transportation vehicle or trailer. Because 

of its high gradeability, the machine can be driven under its own power on to a standard 

loading ramp (Up to 14 degrees). 
It is recommended to reverse the machine up on to the truck thus forward travelling down 

the ramp at the delivery point. Winch-assisted loading is allowable for larger slopes, 

however, operate the trucks assist winch at minimum speed to avoid over-pressurising the 

hydraulic system in the machine. 
When the MB20/26J is on the truck or trailer it should then be made secure by:-

1. Chocking the wheels. 

2. Securing with adequate chains or straps to the lifting lugs on the chassis.

 

Figure 5: Securing the Platform

TOWING & WINCHING VALVES

The fail-safe brakes are automatically applied when the machine comes to a stop or in the 

event of total power loss due to low battery or malfunction of the hydraulic drive system. 
To tow the vehicle or to winch it on to a truck it is necessary to hydraulically bypass the 

control valves and release these brakes.
Make sure the Jib is tied down securely during transport,  DO NOT over tighten straps. 

Straps should have adequate slack so no downward force is applied to the Jib. 

!

!

DO NOT

 loop straps through the cage, ladder or jib as this could 

cause permanent structural damage during transportation.

C A U T I O N

WHEEL CHOCKS

USE 4 SEPARATE 

TIE-DOWNS

Summary of Contents for MB20J

































Reviews: