background image

GB - 5

1. WARNING!

2. DANGER! 

3. DANGER!

EMISSION CONTROL SYSTEM

This equipment and/or its engine may include 
exhaust and evaporative emissions control 
system components required to meet U.S. 
Environmental Protection Agency (EPA) 
and/or California Air Resources Board 
(CARB) regulations.  Tampering with 
emission controls and components by 
unauthorized personnel may result in severe 
fines or penalties. Emission controls and 
components can only be adjusted by an 
Ariens Company dealer or an authorized 
engine manufacturer's service center. 
Contact your Ariens Company Equipment 
Retailer concerning emission controls and 
component questions.

SAFETY RULES

Read, understand, and follow all safety 
practices in owner/operator manual before 
beginning assembly or operating. Failure to 
follow instructions could result in personal 
injury and/or damage to unit.

ALWAYS remove key and/or wire from spark 
plug before assembly, maintenance or 
service. Unintentional engine start up can 
cause death or serious injury.
Complete a walk around inspection of unit 
and work area to understand:

  • Work area   • Your unit   • All safety decals

ALWAYS check overhead and side 
clearances carefully before operation. 
ALWAYS be aware of traffic when operating 
along streets or curbs.

Read Owner/Operator Manual.

Keep people away from unit while 
operating. Keep children out of 
work area and under watchful care 
of a responsible adult.

Never direct discharge towards 
persons or property that may be 
injured or damaged by thrown 
objects.

Stop engine, remove key, read 
manual before making any repairs 
or adjustments.

Wear appropriate hearing 
protection.

ONLY use clean-out tool to clear 
blockages. NEVER use your 
hands.

ROTATING PARTS! ONLY use 
clean-out tool to clear blockages. 
NEVER use your hands. High 
speed impeller rotates below 
discharge opening. Wait for all 
moving parts to stop before 
removing clogs or servicing.

OL4370

OL0910

OL4010

OS6610

ROTATING PARTS. 
Keep clear of auger while engine 
is running.

Read Operator’s Manual.

Allow operation only by 
properly trained adult, 
never children.

Stop engine and remove 
ignition key prior to leaving 
the operator’s position for 
any reason.

Keep all controls, guards 
and safety devices properly 
serviced and functional.

Never direct discharge 
towards persons or 
property that may be 
injured or damaged by 
thrown objects.

OS2080

OL1801

OL4690

Summary of Contents for 920402-Sno-Tek 24E







































Reviews: