SMS TAKEDO-3VF, User Manual

Page: 15 / 75

TAKEDO - 3VF NXP USER MANUAL Release P09.1 dated 01-12-2017
15
5 – KEYPAD AND PROGRAMMING
The control and programming keypad is included in the TAKEDO-3VF NXP. For the instructions for
use, please refer to the original Vacon manual, available on the website: www.vacon.com.
Sub-menus are accessible from the main menu using the key. The M on the first line of the text indicates
the main menu . It is followed by a number designating the relative sub-menu . The arrow (
→ → → →
) in the bottom
right corner of the display indicates an additional sub-menu that can be retrieved by pressing
the key. To go back to the main menu from the sub-menu, just press the key.
Data are split into menus and submenus on the keypad. Each main menu has seven levels M1 - M7.
Press the or keys to go to another menu.
M1 =Monitor M5 =Fault History
M2 =Parameters M6 =System Menu
M4 =Active Faults M7 =Expander Boards
Each menu contains submenus, which can also be on several levels. To access the submenus, press
the key, then use the +/- keys to show the various quantities; to quit the submenu, press the key.
KEY TO SYMBOLS CONTAINED IN MENUS AND SUBMENUS:
M = Menu (internal modes G,V,P,H,F)
V = Read only
G = Group (internal modes V,P) H = Fault history
P = Modifiable parameter F = Active faults
5.0 COPYING PARAMETERS USING THE KEYPAD
The programming keypad can also be used to copy parameters to or from the inverter. This function is very
useful when you need to transfer the optimal parameter set found for a lift on another lift of the same
type, but YOU CAN ONLY USE IT TO COPY PARAMETERS BETWEEN INVERTERS EQUIPPED WITH
THE SAME APPLICATION SOFTWARE RELEASE
(the Application software release is written on a label
under the keypad).
5.0.1 – COPYING FROM INVERTER TO KEYPAD
Press the left arrow until "M" appears in the top left followed by the menu number (eg. M2).
Press the up or down arrow keys to reach M6. Follow the instructions on the display:
5.0.2 – COPYING FROM KEYPAD TO INVERTER
The same method as described above applies.
Selecting S6.3.3 instead of S6.3.2 results in "From the panel" instead of "To the Panel" being shown on the
display. Then continue as before.
Note : During the copy from keypad to inverter some data copy will appear as “Locked” . This happens
because there are fixed parameters that are not modifiable (reserved). If the Enter key is pressed at
any time, “Locked” appears (about 6-7 times), copy continues and “OK” will be displayed.
Attention: Copy from a keypad when its data comes from an inverter of the same size of the one you
are copying into.
Connecting the keypad to the inverter in which you want to copy the data , it will appear:
M6
System menu
S1>S8
→
S6.1 appears when you
press the right
arrow.Press the up arrow
until you reach S6.3.
S6.3
TransferParam
P1>P4
→
S6.3.1 appears when you
press the right arrow.
Press the up arrow until
you reach S6.3.2.
S6.3.2
To Panel
Select
→
Press the right arrow.
S6.3.2
To Panel
AllParameters
Press enter to start
copying parameters.
S6.3.2
To Panel
Wait .....
Wait for copying to
complete.
S6.3.2
To Panel
OK
Copying complete. The
control panel now
contains the inverter data.
Copy To Panel?
enter/reset
Push RESET because
you want to copy the
control panel data to
the inverter.
Copy From
Panel?
enter/reset
Press ENTER to start
copying then wait.