SMP ZINGO MAGIA X-012/P Installation Instructions Manual Download

Page: 44 / 48

ZINGO X-012

Page 40

59) In all fixing positions on the steel work that have not been utilised, the protective plug should be removed and

the permanent black protective plug (item 79) inserted & knocked home with a soft hammer.

60) In all the unused pre-inserted holes in the legs insert and knock home with a soft hammer the black plastic

plug (item 81).

61) On all the Clamp Rings (item 44) that have not been attached to the legs using the M6 x 25 Resistorx bolt

(item 53) insert and knock home with a soft hammer the white plastic plug (item 80) into the appropriate hole.

POST INSTALLATION INSPECTION

CHECK

TICK

All fixings are tightened to there appropriate torque settings and have no protruding sharp
edges.

Paint work is not damaged. (Any making good should be carried out using the procedure in
the Inspection and Maintenance instructions).

Concrete foundations are secure.

Concrete has a water shed away from legs.

Adequate provision of impact absorbing surfacing and no trip points within the minimum
space.

Ensure all unused fixing holes in steel work, pre-inserted holes in legs and unused fixing
holes in clamps have the correct plastic plug fitted.

Ensure that the Telescope can rotate and tip with some resistance.

Site is clear of all tools and rubbish.

Remove any warning signs.

ISSUE B

Summary of Contents for ZINGO MAGIA X-012/P

















































Search results

Summary of Contents for ZINGO MAGIA X-012/P

Reviews:

Related manuals for ZINGO MAGIA X-012/P

Brands by name

Popular brands

SMP ZINGO MAGIA X-012/P, Installation Instructions Manual

Search results

Summary of Contents for ZINGO MAGIA X-012/P

Reviews:

Related manuals for ZINGO MAGIA X-012/P

Brands by name

Popular brands