background image

 

This warranty does not apply to failures caused by outside influence. Items considered to be outside influence 

include, but are not limited to, weather, storage practices, contamination, use of unapproved coolants, lubricants, 

additives, or chemicals, etc. 

 
This warranty does not apply to normal “wear and tear” items. Normal “Wear and Tear” includes, but is not limited 

to, damage to seats due to wear or abrasion, worn painted surfaces, scratched decals or windows, etc.  

 
Smithco may require the return of failed parts or components in order to determine the validity of any warranty 

claim.   

 
Smithco will not be obligated to replace components of other manufacturers if inspection by the original 

component manufacturer indicates that failure was due to normal wear and tear, expected consumption through 

use or improper care or service. 

 

 

 

Other Legal Disclaimers: 

 

The above remedy for product defects through repair or replacement by an authorized Smithco distributor or dealer is the 

purchaser’s sole remedy for any defect. This warranty gives you specific legal rights, and you may also have other rights 

which vary from state to state.  

THERE ARE NO OTHER EXPRESS WARRANTIES OTHER THAN THOSE SET FORTH ABOVE. ALL IMPLIED 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE DURATION OF THE 

LIMITED WARRANTIES CONTAINED HEREIN. 

 

Some states may not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to 

you.  

THE SMITHCO COMPANY IS NOT LIABLE FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL 

DAMAGES IN CONNECTION WITH THE USE OF THE PRODUCT, INCLUDING ANY COST OR EXPENSE OF 

PROVIDING A SUBSTITUTE PRODUCT OR SERVICE DURING PERIODS OF MALFUNCTION OR NON-USE. 

 

Some states may not allow the exclusion of indirect, incidental or consequential damages, so the above exclusion may 

not apply to you. 

Smithco neither assumes, nor authorizes any person to assume for it, any other liability in connection with the 

sale or use of this product.

Summary of Contents for 20-700-A

























































































































Reviews: