background image

 

Air Dryer

                                                                                       

2 Transportation / Installation

 

 

 

Specification of power cable 

Prepare following power cable. 

 

Power cable: 1.25mm

2

(16AWG), External diameter: about 8 ~ 12mm 

IDU22E 

75E-30 (3 phase power supply) …4 cores (including grounding) 

Additional length of about 0.2m is needed to wire inside of the product. 

Length of the power cable 

The length of the power cable should extend less than 30m from the product. 

Connecting to the power supply 

Connect the power cable and the earth to the terminal block. M3 screw is used for the connection part. Make sure 

to use round crimped terminal. 

Applicable crimped terminal: 1.25-3 (Width: 6.5mm and below) 
 

Wiring procedure 

Remove the front panel. 

Insert the cord through the rubber grommet and connect it to the terminal block (refer to the label on the terminal 

block).

 

M3 screw tightening torque: 0.6~1Nm 

 

During wiring work, do not touch other sections except terminal block. 

Attach the front panel as it were. 

 

2 - 3  

Cautions about Reinstallation 

 

Caution 

No one but someone who has enough knowledge about the product and incidental 
devices should reinstall in another place. And following instructions must be executed. 

If you move the product and reinstall it into another place after some operations (including trial running), 
instructions that are not only following ones but also all of those in the chapter 2 should be followed. 

 
Disassembly of the power cable 

Cut off the power source when you disassemble the power cable. 

Warning 

No one but qualified personnel should do the electric wiring. 
Cut off the power supply for safety before the wiring. Do not work under energized 
condition. 

Disassembly of the air piping 

Warning 

No one but qualified personnel should do the air piping. 

Separate the compressor from the product for safety before removing the iping. Do not 

remove any piping when there is remaining compressed air pressure inside of it.

 

Remove the s

eal tape completely after detaching the piping. Remained tape will cau

se imperfect 

cooling and failure by entering into the body of the product.  

 

Residual compressed air pressure release procedure 

Even while the dryer is removed, only when compressed air is 
needed, open the bypass piping valve. 

Close the compressed air inlet and outlet valve. 

Make sure the ball valve located next to the auto drain opened. 

Case Assembly

The ramainder depressure cock.

It opens when turning in the

    drection og the arrow of figure.

Open the auto drain residual pressure release valve 

to release air pressure inside the product. Refer to

 

 

the figure at right. 

Summary of Contents for IDU11E-23-C,K,L,R,T,V

































Reviews: