SMC Networks EX260-FPS1 Operation Manual Download Page 33

Page: 33 / 48

- 32 -

No.EX

※※

-OMU1006-B

9. Troubleshooting

9.1. Troubleshooting

Table 9-1 Troubleshooting for network communication

No.

Problem

Possible cause

Remedy

L/A indicator is OFF

No physical connection to Ethernet
network

●Check the cable connection
●Check network settings

Auto-negotiation not successful

L/A indicator is Green ON

Connection via Ethernet is OK, but no
connection to the PROFINET
Controller (no PROFINET Controller
available on the Ethernet)

●Check network settings
●Check PROFINET controller is active

BF indicator is Red ON

No physical connection on both
PROFINET communication connector

●Check the cable connection
●Check network settings
●Check the L/A indicators

Auto-negotiation not successful

BF indicator is Red flashing

The SI Unit is connected to the
Ethernet network, but the following
problem has occurred

---

●The SI Unit is not connected to the

PROFINET Controller

●Check the cable connection
●Check network settings
●Check PROFINET controller is active

●Configuration is defective

Check the configuration

●Device name is not correct

Check the Device names

●The GSD file is not correct

Check the GSD file

●The PROFINET Controller is

defective

Check the PROFINET Controller

Table 9-2 Troubleshooting for diagnostic events

No.

Problem

Possible cause

Remedy

SF indicator is Red ON

Power supply is outside the specified
voltage range

●Check the PWR and PWR(V)

indicators

●Check the power supply and supply

voltage level

The SI Unit entered high voltage safe
status

●Check the power supply voltage level

and remedy.

At least one valve coil has a short
circuit

Check the solenoid valves for any
short circuit

Self-test has failed

●Reset the power supply
●Check the diagnostic message

The PROFINET Controller is defective

●Check the PLC mode

2020-10-30 10:03

DL085648

Summary of Contents for EX260-FPS1

















































Search results

Summary of Contents for EX260-FPS1

Reviews:

Related manuals for EX260-FPS1

Brands by name

Popular brands

SMC Networks EX260-FPS1, Operation Manual

Search results

Summary of Contents for EX260-FPS1

Reviews:

Related manuals for EX260-FPS1

Brands by name

Popular brands