SMC Networks Barricade Cable/DSL Router User Manual Download

Page: 40 / 40

-39-

C.2 MediaOne

Be sure you have a computer that is already set up to access MediaOne and that the

MAC address of the Ethernet adapter used in this computer is the one registered with

your ISP. Please use this computer and Ethernet adapter to perform the following

steps.

Connect the Ethernet adapter to any LAN port of the Barricade and connect the cable

modem to the WAN port of Barricade.

Power on the Barricade. After it is working, please run WINIPCFG in your Windows

platform and release and renew the IP address manually. This step ensures that your

PC obtains the correct TCP/IP setting from the newly configured Barricade.

Primary Setup

Configure the WAN type as "

Dynamic IP Address.

Save the setting for "

Primary Setup

Click "

Toolbox

" and check the WAN's MAC Address.

Click "

Clone MAC

" button. It will copy the MAC address of the Ethernet adapter used

in your computer and change the WAN's MAC Address.

Reboot Barricade.

NOTE: You can restore the WAN's MAC Address by clicking the "Restore MAC" button.

Summary of Contents for Barricade Cable/DSL Router









































Search results

Summary of Contents for Barricade Cable/DSL Router

Reviews:

Related manuals for Barricade Cable/DSL Router

Brands by name

Popular brands

SMC Networks Barricade Cable/DSL Router, User Manual

Search results

Summary of Contents for Barricade Cable/DSL Router

Reviews:

Related manuals for Barricade Cable/DSL Router

Brands by name

Popular brands