background image

Smarty

MADS

Page 3 of 16

CAUTION

This 

MADS

  product  is  intended  for  use  on  unmodified  stock  engines.    Remove  any  performance

enhancing electronic devices and make sure the ECM has been returned to STOCK if  you have used
another manufacturer’s programmer before the Smarty Micro Tuner.

The use of this product to change the performance characteristics of your vehicle could invalidate the
warranty  provided  by  the  vehicle  manufacturer.    Consult  your  vehicle  warranty  before  using  the
product on your vehicle.

NEVER CONNECT BOTH THE SMARTY CONNECTORS AT THE SAME TIME!
This could damage Smarty and the computer USB port.

NEVER UNPLUG SMARTY WHILE IT IS UPDATING YOUR ECM.
Smarty can recover without pulling fuses, or disconnecting batteries, BUT do not intentionally create
this  situation.    When  Smarty  is  DONE  with  ECM  updates,  ABS  changes,  or  clearing  DTC  codes,  it
may be unplugged, even if Smarty does not display the typical “Unplug Smarty  and Turn Key OFF”
screen.

It  is  recommended  that  you  do  not  store  your  Smarty  Micro  Tuner  in  your  vehicle  if  ambient
temperatures  in  your  area  fall  below  32°F.    Excessively  low  temperatures  can  cause  malfunction  or
damage to Smarty Micro Tuner that is not covered by the MADS warranty.

In  the  case  of  ECM  replacement,  restore  the  ECM  back  to  the  STOCK  software  before  the  ECM
replacement.  Smarty works only with one vehicle and one ECM at a time while it is VIN Locked.
Under  no  circumstances  we  will  refund,  repair,  or  warranty  units  that  are  send  in  and  result  VIN  #
locked.

RESTORE ECM TO STOCK SOFTWARE BEFORE ANY SERVICE ASSISTANCE.
If you need to return your vehicle to a service center, restore the vehicle ECM to its STOCK program
by following the instruction in this manual.  The service center might reprogram your vehicle with an
updated,  STOCK,  software  ECM  reflash 

without

  your  knowledge.    If  your  vehicle  has  not  been

returned  to  its  STOCK  program  prior  to  a  service  visit  and  the  ECM  is  reflashed,  the  Smarty  Micro
Tuner  will  no  longer  be  able  to  program  your  vehicle.    Such  failure  is  not  covered  by  the 

MADS

warranty.    Under  no  circumstances  will  we  refund,  repair,  or  warranty  units  that  are  sent  in  that  are
locked.

Summary of Contents for MADS S-06

















Reviews: