background image

 

 

75mm X 2 

40mm X 2 

BACK WALL 

SIDE 

WALL 

SIDE   

OVERLAPS 

BACK 

75mm X 2 

BACK WALL 

SIDE 

WALL 

SIDE   

OVERLAPS 

BACK 

40mm X 2 

10 

TOP PLATE 

TOP PLATE 

BOTTOM PLATE 

BOTTOM PLATE 

FRONT  

OVERLAPS 

SIDES 

X 4 

SIDE 

WALL 

BACK WALL 

SIDE 

WALL 

FRONT WALL 

X 4 

X 4 

X 4 

TOP PLATE 

BOTTOM PLATE 

SELECT: 

 

4 x Pre-made Wall Panels 

12 x 40mm Screws 

4 x 75mm Screws 

16 x Rivets 

 

STEP 1: 

 

 

Stand the Back Panel and the Side Panel 
up using someone to support the panels     
while they are screwed together.  

 

 

Before fixing, ensure that the Side Panel 
overlaps the Back Panel.  

 

 

Using 4 x 75mm screws, screw the Top 
Plates together. 

 

 

Using 4 x 40mm screws, screw the Bot-
tom Plates together. 

STEP 2: 

 

 

Repeat Step 1 with the second Side Panel, 
ensuring that the Side Panel overlaps the 
Back Wall Panel

STEP 3: 

 

 

Stand up the Front Wall Panel. 

 

 

Ensure that the Front Wall Sheets overlap 
the Side Wall Sheets. 

 

 

Using 8 x 40mm screws (2 per join) screw 
the Top and Bottom Plates together in the 
corners

.

 

STEP 4: 

 

 

Rivet the wall sheets together at the corners 
using 4 equally spaced rivets as shown. 

WALL PANEL ASSEMBLY 

Summary of Contents for SS2010
















Reviews: