background image

 

 

15mm 

15mm 

15mm 

15mm 

ASSEMBLE FRONT PANEL 

BOTTOM PLATE 

1811mm 

1811mm 

TOP PLATE 

530mm

 

960mm

 

TOP PLATE 

DOOR OPENING 

Plan View

 

TOP

 

PLATE

 

DOOR

 

JAMB

 

NAIL

 

x3

 

x3

 

x3

 

SELECT: 

 

2 x 1.850 Wall Sheets 

1 x 2.020 Top Plate (Red) 

1 x 2.020 Bottom Plate (Green) 

2 x 1.850 Door Jamb Flashings 

28 x 30mm Galv Clouts 

17 x Rivets 

STEP 1: 

 

 

Lay out 1 x Top Plate and 1 x Bottom Plate on a flat 
surface as shown  

STEP 2: 

 

 

Using 2 x 30mm clouts, nail the Door Jamb Flashing flush with 
the top of the Top Plate at the correct  measurement as shown 
in plan view. Pre drill holes using a 3.5mm drill bit 

 

 

Check the distance between the top and bottom plates then use 
a further 2 x 30mm clouts to nail the Door Jamb Flashings to 
the bottom Plate. Pre drill holes. 

STEP 4: 

 

 

Place the door on the panel (In open position, approx 5mm 
below top plate). Using two rivets, rivet the top and bottom 
hinges to the Door Jamb Flashing.  

 

 

Ensure the door closes properly, then fit remaining rivets. 

STEP 3: 

 

 

Place 2 x Wall Sheets on timber. 

 

 

Ensure that the top of the sheets are flush with the top of the 
Top Plate and that the sides of the wall sheets overhang the 
Top Plate by 

15mm

 as shown. Nail wall sheets to Top Plate 

(two clouts per pan) 

 

 

Nail the wall sheets to the Bottom Plate making sure that the 
Plates are the correct distance apart and that the sides of the 
wall sheets overhang the Bottom Plate by 

15mm

 

 

Drill & rivet Door Jamb Flashings to wall sheets using four 
rivets equally spaced on each side. 

NOTE: 

The

 

Doorway is standard at 530mm from left-hand end. 

To shift the doorway to the right-hand side of the front 

wall, simply measure 530mm from the right-hand end.

 

NOTE: 

Door can be hinged on either side.

 

IMPORTANT—IF YOU CHOOSE TO RAISE YOUR TIMBER 

BASE PLATE –READ THE FOLLOWING; 

 

For sheds with Raised Base Plate option only (see page 5), deduct 

30mm from measurement shown between Top and Bottom Plates on 
all wall panels, so cladding protrudes 20mm below bottom plate

Summary of Contents for SS2010
















Reviews: