background image

7

1x 24 sec 

...1x

...2x

...3x

+

 

...

A

1x 24 sec 

...1x

...2x

...3x

+

 

...

B

1x 24 sec 

...1x

...2x

...3x

+

 

...

Activate 

12HR

C

Deactivate

1x 24 sec 

...1x

...2x

...3x

+

 

...

Activate 

24HR

D

This feature will operate the faucet every 12 or 24 hours since last use, if not used 
to prevent stagnant water conditions.

Default purge duration is two minutes.

Consult factory regarding other timing options.

IR activation (see above). 
Cover IR clic approximately 
24 sec. (ignore LED 
indications during this 
period). Release when 
requested program is 
reached. (See diagram 
to right). Programming 
mode will time out after 2 
minutes if no changes are 
made.

SENSOR RANGE ADJUSTMENT

FACTORY SETTING IS APPROPRIATE FOR THE MAJORITY OF APPLICATIONS AND SHOULD NOT REQUIRE RESETTING UNLESS UNDER EXTREME SITUA-
TIONS: HIGH REFLECTION OR LOW LIGHT.

2x + 

1x 5 sec

1x

2x

3x

4x

6x - Factory Setting

Longer

Distance

Shorter

Distance

7x

8x

5x

2x + 

1x 5 sec

1x

2x

3x

4x

6x - Factory Setting

Longer

Distance

Shorter

Distance

7x

8x

5x

2x + 

1x 5 sec

1x

2x

3x

4x

6x - Factory Setting

Longer

Distance

Shorter

Distance

7x

8x

5x

2x + 

1x 5 sec

1x

2x

3x

4x

6x - Factory Setting

Longer

Distance

Shorter

Distance

7x

8x

5x

A

2x + 

1x 5 sec

1x

2x

3x

4x

6x - Factory Setting

Longer

Distance

Shorter

Distance

7x

8x

5x

C

D

IR Activation (see page 5).To enter 
programming mode place finger on IR 
clic for 2 times then remove. Light on 
side of crown should blink to indicate 
programming mode. 

Wait, until LED flashes GREEN.

B

Cover IR clic until LED flashes RED 4 times – hold IR clic until LED flashes 
1 time to 8 times from minimum to maximum range. See diagram below. 
Release when requested range is reached.

12/24 LINE PURGE FEATURE

Summary of Contents for BASYS EFX-8













Reviews: