SLEIPNER MOTOR AS SE 125 S Installation And User Manual Download Page 19

 19

SE 30/125 S - SE 40/125 S - SE 60/185 S

    

1.0.1- 2008

Important user precautions

GB

•  Forviss deg om at du kjenner plasseringen av hovedstrømsbryteren 

til baugthrusteren, som kutter all strøm til thrusteren, så thrusteren 

kan skrus av i nødstilfelle.

•  Før berøring av noen del av thrusteren må alltid strømmen skrus av. 

En tilfeldig start kan volde stor fysisk skade.

•  Skru alltid av kontrollpanelet etter bruk.

•  Den maksimale sammenhengende kjøretiden for en elektrisk 

thruster er ca. 3 min. da vil en føler automatisk skru av motoren når 

den når en viss varme. Dette må tas i betraktning når en manøver 

planlegges.

•  Dette betyr at ved manøvere som tar lang tid vil ikke thrusteren 

kunne brukes hele kontinuerlig. Ved manøvere som tar lang tid kan 

man bruke thrusteren i ca 10 % av tiden, avhengig av tempraturen i 

vannet. 

•  Bruk aldri thrusteren når noen er i vannet, thrusteren vil trekke gjen

-

stander til seg og kontakt med propellen vil volde alvorlig skade.

•  Kjør aldri thrusteren i mer enn 1 sek. når båten er på land. Uten 

motstand fra vannet vil thrusteren nå ødelegende turtall svært fort.

•  Hvis thrusterne stopper å gi skyvekraft mens motoren er i gang, er 

det trolig oppstått problemer i girsystemet. Stopp umiddelbart å kjøre 

motoren, og skru den av. Uten motstand fra vannet vil thrusteren nå 

ødelegende turtall svært fort.

•  Når man forlater båten skal alltid hovedstrømsbryteren slås av.

•  Vi anbefaler å ha motoren i gang når thrusteren kjøres. Da vil bat

-

terien vedlikeholdes, og det vil være høyere spenning til elektromo-

toren. Høyere spenning gir høyere turtall og bedre ytelse.

•  Ytelsen til en baugthruster avhenger av hvilken spenning motoren 

mottar under kjøring. Kapasiteten til batterier avtar etter hvert som 

de blir eldre, og dermed også ytelsen til thrusteren. Ved å installere 

nye batterier vil thrusteren yte maksimalt igjen.

•  Kun en kontroll skal brukes av gangen, hvis to kontroller brukes mot-

satt vei vil thrusteren stoppe automatisk. Hvis to paneler opereres 

samme vei vil ikke dette skje.

•  Hvis thrusteren ikke fungerer tilfredsstillende må feilen lokaliseres 

og rettes så snart som mulig, for at ikke thrusteren skal ta ytterligere 

skade, skru av hovestrømsbryteren hvis feilen er av elektrisk art.

Viktige brukerforebehold

N

•  Ensure that you know the location of the main battery switch that  

  disconnects the thruster from all power sources (batteries) so that  

  the thruster can be turned off in case of a malfunction.

•  Always turn the main power switch off before touching any part of  

  the thruster, as an incidental start while touching moving parts can  

  cause serious injuries.

•  Always turn the control device off when the thruster is not in use.

•  The maximum continues usage time of the electrical thruster is  

  approximately 3 minutes. The electromotor has a built in thermal  

  cut-off switch that will shut off the electromotor if it is overheating  

  and re-engage it when it has cooled down some. This should be  

  considered when planning your maneuvering.

•  This also means that the thruster will limit its total running time per 

  time period so that you can not count on the thruster to hold you  

  in a current and side wind for extensive time periods. Depending  

  on the surrounding temperatures etc. the thruster will be able to  

  run approximately 10 % of the time.

•  Never use a thruster close to somebody in the water, as the  

  thruster will draw objects close by into the tunnel and contact with 

 

  the rotating propellers will cause serious injuries.

•  With the boat on land, only run the thruster for a fraction of a 

  second, as without resistance it will accelerate very fast to a  

  damaging rpm. Also, while the thruster is in air, make sure that the  

  propellers have come to a complete stop before performing a  

  directions change of the thruster, as it might cause damage to the  

  thruster.

•  If the thruster stops giving thrust while the electromotor is running,  

  chances are that there is a problem in the drive-system. You must  

  then immediately stop trying to run it, and turn it off, as running the  

  electromotor for more than a few seconds without resistance from  

  the propeller, can cause serious damage to the electromotor.

•  When leaving the boat always turn off the main power switch for  

  the thruster.

•  We advice to always keep the main engine(s) running while using a 

  thruster. This will keep the batteries in a good charge condition. This 

  will also give better performance to the thruster, as a higher voltage    at 

the thruster results in a higher torque (power) in the electromotor.

•  Please note that the performance of a thruster strongly depends on 

  the voltage available at the electromotor. This voltage will decrease  

  by time because aging batteries have a reduction of capacity. By  

  installing new batteries the effect of the thruster should be back at  

  the original level.

•  Make sure that only one control is used at the same time, if two  

  panels are operated in opposite directions at the same time the  

  thruster will not run at all. If they are operated in the same direction  

  the thruster will run in this direction.

•  If the thruster is not performing or functioning as usual, the cause for  

  this must be found and corrected as soon as possible so to avoid  

  causing any other or further damage to the equipment. You must  

  also turn off the main battery switch immediately in case the  

  problem is of electric origin.

•  Never store anything (e.g. equipment, sails, ropes etc.) in the  

  same compartment as the thruster. When the thruster runs for  

  a longer period it will get hot and will cause damage.

Summary of Contents for SE 125 S





























Reviews: