background image

6

Installation

User Manual

SKOPE OD460

Enclosed installations

Enclosed installations must have the following minimum clearances around
the cabinet, and include the following features:

75mm behind the cabinet.

An air guide must be used to ensure all refrigeration exhaust air is 
directed up and away from the cabinet.

The air guide must also ensure the air exhaust outlet cannot be blocked 
by product or other items above the cabinet.

Refrigeration exhaust air must 

NOT 

be allowed to run horizontally across the 

top of the cabinet, as it may be pulled down into the cabinet interior. 

30mm 

(rear spacer)

60mm

(min)

60mm

(min)

200mm

(min)

Free-standing installation ventilation requirements

Air 

intake  

Front

Back wall

Exhaust air

Exhaust air

Air guide

Enclosure ceiling

Air intake  

Front

Enclosed installation ventilation

Exhaust air

Exhaust air must 

NOT

 run across 

top of cabinet

Enclosure 

back wall

75mm

(min)

Exhaust air

Exhaust air

Air 

intake  

Front

Enclosure ceiling

Air guide

Enclosure 
back wall

Exhaust air 

must 

NOT

 

run across 

top of 

cabinet 

Enclosed installation ventilation requirements

Summary of Contents for OD460




















Reviews: