Skoda Octavia III 2013 Service Manual Download Page 49

Page: 49 / 172

– Unplug connector -1-.
– Unlock catches -arrows-, remove air guide pipe.

– Press release buttons on the hose -1- to remove the activated

charcoal filter.

– Unscrew screws -arrows- and pull out, pull off hose for crank‐

case ventilation.

Note

♦

If one or more O-rings are damaged, replace the hose for the

crankcase ventilation.

♦

Wet new O-rings with engine oil prior to installation!

– Unclip the electric wiring harness -arrows-.
– Unscrew screws -1, 3- and remove toothed belt guard -2- for

coolant pump toothed belt.

– Turn the crankshaft on the fixing screw of the belt pulley crank‐

shaft in direction of running of the engine and check the

complete toothed belt for the following conditions -arrows-:

Octavia III 2013 ➤ , Octavia III 2014 ➤

Maintenance - Edition 12.2014

3. Engines

ProCarManuals.com

Summary of Contents for Octavia III 2013













































































































































































Search results

Summary of Contents for Octavia III 2013

Reviews:

Related manuals for Octavia III 2013

Brands by name

Popular brands

Skoda Octavia III 2013, Service Manual

Search results

Summary of Contents for Octavia III 2013

Reviews:

Related manuals for Octavia III 2013

Brands by name

Popular brands