Introduction
P13
-13-
圖
13/Fig. 13
傾 放與扳 回 機頭
LEAN & RECOVER
THE MACHINE HEAD
進 行 維 修 或 調 整 時 , 為 了 避 免 突 發 狀 況 發 生 而 導 致 意 外 , 請 務 必 先 關 閉 電 源 再
進 行 操 作 ; 需 要 將 機 台 傾 放 縫 紉 機 , 請 注 意 手 指 被 縫 紉 機 或 送 釦 機 給 夾 傷 , 尤
其 是 扳 回 機 頭 時 。
For avoiding the emergency or accidence, please make sure to turn off the power to
operate when doing maintenance or the adjustment. It is needed to lean he sewing
machine, and please pay attention your fingers not to be pinched , especially when
recovering the machine.
縫 紉 機 與 送 釦 機 是 固 定 在 同 一 板 子 上 ,
不 需 擔 心 兩 者 配 合 問 題 , 使 用 者 僅 需 固
定 於 桌 板 , 即 可 準 備 車 縫 鈕 釦 。 為 求 機
頭 的 穩 定 度 , 在 板 子 底 部 裝 有 一 螺 絲
固 定 。 因 此 若 要 將 機 頭 傾 倒,需 將 螺 絲
鬆 開 。 需 將 機 頭 歸 位 時 , 要 注 意 機 頭 輕
輕 扳 回 , 且 小 心 手 指 被 壓 傷 ; 也 不 可 過
猛 扳 回 , 以 免 損 壞 機 座 及 基 準 變 動 。 當
縫 紉 機 定 位 後,再 將 螺 絲 鎖 回 。(圖
)
13
Due to the sewing machine and the feeding
button machine are fixed on the same board,
there is
no worry about the combination.
Users merely fix the machines on the table and
then it can start the task. Keeping the stability,
there is a screw under the board to fix the
machine. Thus, if leaning the machine head,
loosening the screw first. When recovering
the machine head, pay attention to put it gently
and be careful of fingers from being hurt. Not
to move back forcefully, it is easy to damage
the bottom and the benchmark. After fixing the
machine, fasten the screw
.
(
Fig.13)
-13-
圖
13/Fig. 13
傾 放與扳 回 機頭
LEAN & RECOVER
THE MACHINE HEAD
進 行 維 修 或 調 整 時 , 為 了 避 免 突 發 狀 況 發 生 而 導 致 意 外 , 請 務 必 先 關 閉 電 源 再
進 行 操 作 ; 需 要 將 機 台 傾 放 縫 紉 機 , 請 注 意 手 指 被 縫 紉 機 或 送 釦 機 給 夾 傷 , 尤
其 是 扳 回 機 頭 時 。
For avoiding the emergency or accidence, please make sure to turn off the power to
operate when doing maintenance or the adjustment. It is needed to lean he sewing
machine, and please pay attention your fingers not to be pinched , especially when
recovering the machine.
縫 紉 機 與 送 釦 機 是 固 定 在 同 一 板 子 上 ,
不 需 擔 心 兩 者 配 合 問 題 , 使 用 者 僅 需 固
定 於 桌 板 , 即 可 準 備 車 縫 鈕 釦 。 為 求 機
頭 的 穩 定 度 , 在 板 子 底 部 裝 有 一 螺 絲
固 定 。 因 此 若 要 將 機 頭 傾 倒,需 將 螺 絲
鬆 開 。 需 將 機 頭 歸 位 時 , 要 注 意 機 頭 輕
輕 扳 回 , 且 小 心 手 指 被 壓 傷 ; 也 不 可 過
猛 扳 回 , 以 免 損 壞 機 座 及 基 準 變 動 。 當
縫 紉 機 定 位 後,再 將 螺 絲 鎖 回 。(圖
)
13
Due to the sewing machine and the feeding
button machine are fixed on the same board,
there is
no worry about the combination.
Users merely fix the machines on the table and
then it can start the task. Keeping the stability,
there is a screw under the board to fix the
machine. Thus, if leaning the machine head,
loosening the screw first. When recovering
the machine head, pay attention to put it gently
and be careful of fingers from being hurt. Not
to move back forcefully, it is easy to damage
the bottom and the benchmark. After fixing the
machine, fasten the screw
.
(
Fig.13)
Summary of Contents for Sew Reach ABF Series
