SimpliFire SF-ALL48-BK Service Manual Download

Page: 9 / 11

SimpliFire • SF-ALL48-BK, SF-ALL60-BK Service Manual Rev. B • 2040-960 • 3/18

Control Board Installation

23. Remove the two (2) Phillips screws. After removing

screws the mounting bracket can be lowered down

to access the wires. See Figure 23.

Figure 23. Remove Mounting Bracket Screws

24. Unplug the five (5) pin and socket connectors

between the Control Board and the wire harnesses.

Tag and label the wire harnesses to ensure that

wires will be reconnected correctly. See Figure 24.

Figure 24. Unplug Control Board

25. Install new Control Board and reverse the installation

steps.

Blower/Heater Installation

26. Locate the four (4) screws on the mounting plate for

the blower/heater module. See Figure 25.
27. Remove the four (4) Phillips screws.

Figure 25. Remove Mounting Plate Screws

28. Drop the Blower/Heater module down on the shelf.

See Figure 26.
29. Reach up into the right end of the slot, and unplug

the cable from the connector.

Figure 26. Remove Blower/Heater

30. Install new Blower/Heater and reverse the installation

steps.

SCREWS

MOUNTING BRACKET

SHELF

Summary of Contents for SF-ALL48-BK












Search results

Summary of Contents for SF-ALL48-BK

Reviews:

Related manuals for SF-ALL48-BK

Brands by name

Popular brands

SimpliFire SF-ALL48-BK, Service Manual

Search results

Summary of Contents for SF-ALL48-BK

Reviews:

Related manuals for SF-ALL48-BK

Brands by name

Popular brands