Simex SPI-638, User Manual

Page: 52 / 68

User manual - FLOW METER SPI-638
Register Write Range Register description
25h Yes 0 ÷ 5
“rESP” parameter in “rS-485” menu (additional response delay);
0 - no additional delay; 1 - ” 10c ” option; 2 - ” 20c ” option;
3 - ” 50c ” option; 4 - ” 100c ” option; 5 - ” 200c ” option;
27h Yes 0 ÷ 99
“mbtimE” parameter in “rS-485” menu (maximum delay between
received frames); 0 - no delay checking;
1 ÷ 99 - maximum delay expressed in seconds
28h Yes 0 ÷ 1 “ AL ” parameter in “ bEEP ” menu: 0 - off; 1 - on
29h Yes 0 ÷ 1 “ r1 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Ah Yes 0 ÷ 1
“ r2 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Bh Yes 0 ÷ 1 “ r3 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Ch Yes 0 ÷ 1 “ r4 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Dh Yes 1 ÷ 8
“ briGHt ” parameter (display brightness);
1 - the lowest brightness; 8 - the highest brightness
2Fh Yes 0 ÷ 1
“ Edit ” parameter (numerical parameters edit mode);
0 - „ dig ” mode; 1 - „ SLid ” mode
Parameters or relay R1 operation
30h
31h Yes
Yes
0 ÷ 999999 “ SEt P ” parameter in “ rELAy1 ” menu, no decimal point included
32h
33h Yes
Yes
0 ÷ 99999 “ HySt ” parameter in “ rELAy1 ” menu, no decimal point included
34h Yes 0 ÷ 5
“ modE ” parameter in “ rELAy1 ” menu:
0 - “ noACt ” mode; 1 - “ on ” mode; 2 - “ oFF ” mode; 3 - “ in ” mode;
4 - “ out ” mode; 5 - “ modbuS ” mode
35h Yes 0 ÷ 999
“t on”
parameter in
“rELAy1”
menu, expressed in tenth of
seconds or tenth of minutes depend on “unit” parameter
36h Yes 0 ÷ 999
“t oFF” parameter in “rELAy1” menu, expressed in tenth of
seconds or tenth of minutes depend on “unit” parameter
37h Yes 0 ÷ 1
“unit” parameter in “rELAy1” menu:
0 - seconds; 1 - minutes
38h Yes 0 ÷ 2
“ALArmS”
parameter in
“rELAy1”
menu:
0 - no changes; 1 - on; 2 - off
39h
3Ah
Yes
Yes
0 ÷ 999999 “ SEt P2 ” parameter in “ rELAy1 ” menu, no decimal point included
3Bh Yes 0 ÷ 2
“SourCE” parameter in “rELAy1” menu (kind of value controlled
relay): 0 - “FLo”; 1 - “bAt”; 2 - “tot”;
3Ch Yes 0 ÷ 3
“t PrEc” parameter in “rELAy1” menu (precision of thresholds
and hysteresis while relay is controlled due to total flow counter
value):
0 - “ 0”; 1 - “ 0.0”; 2 - “ 0.00”; 3 - “0.000”
3Dh Yes 0 ÷ 1
“t unit” parameter in “rELAy1” menu (the unit of thresholds and
hysteresis while relay is controlled due to total flow counter value):
0
- unit;
1
- 1000un;
52