User manual for - TIMER SLC-94
Register Write
Range
Register description
0Ch
1
Yes
see descr.
Counter control. The control is realised by setting particular bits:
bit 0
=
„1”
– counting start
bit 1
=
„1”
– counting stop
bit 2
=
„1”
– clearing of the main timer
bit 3
=
„1”
– totalizer clearing.
After executing of order, the value of this register is cleared
automatically
Bit
1
(stop) has higher priority than
bit
0
(start), so entering of
value 03h causes in counter stopping.
0Dh
No
0Eh
No
0 ÷ FFFFFFFF
Totalizer value- higher word
Totalizer value- lower word, joined value of registers 0Ch & 0Dh
defined total seconds count
0Fh
No
0 ÷ 999
Totalizer value- miliseconds
10h
No
0 ÷ 3
Relays state in binary format
(1 - closed, 0 - opened):
00 000 000 000 000 ba
a
- relay R1
b
- relay R2
20h
2
Yes
0 ÷ 199
Device address
21h
No
007Bh
Device identification code (ID)
22h
3
Yes
0 ÷ 7
“bAud”
parameter in
“rS-485”
menu (baud rate);
0
- 1200 baud;
1
- 2400 baud;
2
- 4800 baud;
3
- 9600 baud;
4
- 19200 baud;
5
- 38400 baud;
6
- 57600 baud;
7
- 115200 baud
23h
4
Yes
0 ÷ 1
“mbAccE”
parameter in
“rS-485”
menu (permission to write
registers via RS-485 interface);
0
- write denied ;
1
- write allowed
25h
Yes
0 ÷ 5
“rESP”
parameter in
“rS-485”
menu (additional response delay);
0
- no additional delay;
1
- ”
10c
” option;
2
- ”
20c
” option;
3
- ”
50c
” option;
4
- ”
100c
” option;
5
- ”
200c
” option;
2Dh
Yes
1 ÷ 8
“
briGHt
” parameter (display brightness);
1
- the lowest brightness;
8
- the highest brightness
2Fh
Yes
0 ÷ 1
“
Edit t
” parameter (numerical parameters edit mode);
0
- „
dig
” mode;
1
- „
SLid
” mode
30h
Yes
see descr.
Parameter “
Hr”
of
“rELAy1”
/
“SEtP1”
submenu (higher word).
31h
Yes
see descr.
Parameter “
Hr”
of
“rELAy1”
/
“SEtP1”
submenu (lower word).
Joined value of registers 30h & 31h: from 0 to 99 999
32h
Yes
see descr.
Parameter
“min”
of
“rELAy1”
submenu (higher word).
33h
Yes
see descr.
Parameter
“min”
w podmenu
“rELAy1”
submenu (lower word).
Joined value of registers 32h & 33h: from 0 to 999 999
34h
Yes
see descr.
Parameter
“SEC”
of
“rELAy1”
submenu (higher word).
35h
Yes
see descr.
Parameter
“SEC”
of
“rELAy1”
submenu (lower word).
Joined value of registers 34h & 35h: from 0 to 999 999
36h
Yes
see descr.
Parameter
“mSEC”
of
“rELAy1”
submenu (higher word).
29
