Silverline Silverstorm 261884, Original Instructions Manual

Page: 7 / 40

6
GB
p.
Even when this tool is used as prescribed it is not possible to
eliminate all residual risk factors.
If you are in any doubt as to safe
use of this tool, do not use it
Polisher Safety
• DO NOT use this polisher as an angle grinder
• ALWAYS read and understand all information supplied with polishing
pastes before use
• DO NOT smoke, eat, or drink when using this polisher
• NEVER attach any accessory with a maximum speed lower than the no
load speed of the machine
Product Familiarisation
Accessories (not shown)
• 1 x Spare carbon brushes
Intended Use
• Multi-purpose rotary polishing machine, used for light to medium duty
polishing tasks, using suitable polishing bonnets and compounds
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Before use
WARNING: ALWAYS disconnect the machine from the power supply before
fitting or removing backing pads or accessories.
Assembling the front handle
• The Front Handle (9) must be fitted to the machine before use
• Screw the Front Handle (9) clockwise into the mounting point on the gear
housing (see ‘Product Familiarisation’). Tighten by hand
• To remove the handle, unscrew anti-clockwise
Fitting the Backing Pad
• The Backing Pad (2) must be securely fitted to the Spindle (3) before use:
1. Engage the flat part of the Spindle (3) with a suitable spanner, and
hold in position
2. The backing pad can now be screwed onto the spindle and tightened
WARNING: The backing pad is tightened by hand. Take care not to cross-
thread or over-tighten.
3. Remove the spanner
Fitting bonnets, polishing sponges and discs
• The Hook and Loop Polishing Bonnet (1) and other polishing accessories,
such as polishing sponges (not included) can be pressed onto the face of
the Hook and Loop Backing Pad (2)
• Slowly pull the fitted attachment off the hook and loop backing pad to
remove
Note: Always make sure both hook and loop surfaces are free of dirt
and debris prior to attaching any items (also see remarks ‘Maintenance’
section).
Operation
WARNING: ALWAYS wear adequate protective equipment, including eye,
hand and hearing protection, when operating this machine. Use respiratory
protection where dust or fumes are produced.
Switching on and off
WARNING: Never switch the tool on or off when it is in contact with
the workpiece. This can cause serious injury to the operator and will
significantly shorten the service life of the On/Off Trigger Switch (8).
1. Connect the machine to the power supply
2. Hold the tool securely with both hands: one hand on the Main Handle
(7), the other hand on the Front Handle (9)
3. Squeeze the On/Off Trigger Switch (8) to start the tool
4. Allow the tool to reach the speed required before bringing the machine
into contact with the workpiece
5. Remove the polisher from the workpiece before switching off
6. To stop the machine, release the On/Off Trigger Switch
WARNING: ALWAYS wait until the machine has come to a standstill before
putting it down.
Adjusting the tool speed
• The speed of the machine is controlled using the Variable Speed Dial (6):
a higher number indicates a higher speed setting
WARNING:
Always set the speed control dial to the correct speed for the
task at hand.
WARNING: Never exceed the maximum speed of the installed accessory.
Polishing tips
• Ensure that the area to be polished is clean and dry
• Choose only polishing compounds that are compatible with the material
to be polished, and with the method of application. Read and understand
all information supplied with your polishing compound before use
• If using polishing sponges, apply polishing compound evenly to the
polishing sponge and place the sponge against the work surface
• Hold the machine securely, using both hands, by the handles provided.
The polishing sponge should make only light contact with the work
surface
• Switch on the machine, and work across the surface using a wide
'sweeping' motion. Stop and apply extra compound as required
• When the entire surface has been covered, stop the machine and allow
the compound to dry (follow manufacturer’s guidance)
• Attach a clean polishing bonnet to the machine and work across the
surface as before, until all visible polishing compound is removed
Accessories
A range of accessories for your polisher, including lambswool bonnets,
polishing sponges and compounds, is available from your SILVERLINE
stockist. Spare parts can be obtained from www.toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out
any inspection, maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Silverline service centre.
This advice also applies to extension cords used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine’s service life. Clean the body of
your machine with a soft brush, or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
1 Hook & Loop Polishing Bonnet
2 Hook & Loop Backing Pad
3 Spindle
4 Brush Access Plugs
5 Motor Vents
6 Variable Speed Dial
7 Main Handle
8 On/Off Trigger Switch
9 Front Handle
PDF Compressor Pro