![background image](http://html1.mh-extra.com/html/silverline/953452/953452_manual_1273696009.webp)
EN
Original Instructions
silverlinetools.com
9
•
Blades that can be resharpened should be
resharpened only according to the blade
manufacturer’s instructions. These may include a
limited number of times the blade can be
resharpened
•
Sharpened blades should be more thoroughly
inspected before use and replaced immediately if
there is any doubt about their condition and
suitability for use
•
In the event blades encounter an embedded object
in use that the blades are not suitable for, blades
should be replaced immediately
Beware of heat
•
Cutting tools and workpieces may become hot in
use. Do not attempt to change tools until they have
been allowed to cool completely
Control dust / swarf
•
Do not allow dust or swarf to build up. Sawdust is a
fire hazard, and some metal swarf is explosive
•
Be especially careful when cutting wood and metal.
Sparks from metal cutting are a common cause of
wood dust fires
•
Where possible, use a dust extraction system to
ensure a safer working environment
WARNING:
The dust produced from working with some materials can
be toxic. Beech, oak, mahogany and teak natural woods, man-made
composite woods and some surface treatments, including paint with lead,
are toxic. Lead-based paint is common in buildings built before 1960.
Always wear suitable respiratory protection; for example, a respirator face
mask. Use a dust extraction system or regularly vacuum the work area to
prevent the build-up of dust. In addition, vacuum the work area after the
work has been completed. Most dust is a fire hazard. Overhead work
surfaces have an increased safety risk for dust.
Battery and Charger Safety
Use the Battery Charger correctly
•
Refer to the section of this manual relating to use of the
Battery Charger (24) before attempting to charge the
Battery (11)
•
Do not attempt to use the charger with any batteries other
than those supplied.
•
Keep your battery charger clean; foreign objects or dirt may
cause a short or block air vents. Failure to follow these
instructions may cause overheating or fire
•
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard
•
Examine the battery charger regularly for damage,
especially the cord, plug and enclosure. If the battery
charger is damaged, it must not be used until it has been
repaired
•
Children should be supervised to ensure that they do not
play with the appliance
WARNING
: Do not attempt to recharge non-rechargeable batteries.
Battery Safety
WARNING:
Li-ion batteries, if incorrectly used, stored or charged are a
fire, burn and explosion hazard.
•
Keep the battery out of reach of children
•
Only charge Li-ion batteries designed specifically for this
charger
•
Only use Li-ion batteries provided with this product or
specifically designed to be compatible
•
Allow batteries to cool for 15 minutes after charging or
heavy use. Failure to follow these instructions may cause
overheating or fire
•
When not in use batteries should be stored at room
temperature (approximately 20˚C)
•
Ensure battery contacts cannot accidentally short in
storage. Keep batteries clean; foreign objects or dirt may
cause a short. Keep away from other metal objects, for
example paperclips, coins, keys, nails and screws
•
Under abusive conditions, liquid may be ejected from the
battery. This liquid may cause skin irritation or burns. Avoid
contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help
•
Do not open, disassemble, crush, heat above 60°C or
incinerate. Do not dispose of in fire or similar
•
Do not get batteries wet or immerse in water
Battery & charger safety features
The Battery and Charger are fitted with a number of safety features which
may be triggered during charging or operation:
•
Over-charge protection: Charger automatically switches off
when the Battery has reached full charge capacity,
protecting the internal components of the battery
•
Over-discharge protection: Prevents the Battery from
discharging beyond the recommended lowest safety voltage
•
Over-heat protection: Sensor switches off if the Battery
becomes too hot during operation. This can happen if the
tool is overloaded or being used for extended periods of
time. Up to 30 minutes cooling time may be required
depending on the ambient temperature
•
Overload protection: Battery temporarily stops if it is
overloaded or the maximum current draw is exceeded,
protecting the internal components. The Battery will
resume normal operation when the current draw returns to
a normal safe level. This may take a few seconds
•
Short circuit protection: The Battery will stop working
immediately if a short circuit occurs, this prevents damage
to
the Battery or tool
1.
Saw Blade
2.
Shoe
3.
Blade Holder
4.
Blade Release
5.
Secondary Handle
6.
Motor Vents
7.
Trigger Lock Button
8.
ON/OFF Trigger Switch
9.
Main Handle
10.
Battery Charge Indicator
11.
Battery
12.
Battery Mount
13.
Battery Release
14.
Battery Charger
15.
Charger Terminals
16.
Green LED
17.
Red LED
Intended Use
Reciprocating power saw for light to medium duty cutting of wood,
plasterboard, plastic, mild steel, and non-ferrous metals (requiring the
purchase of additional, material-specific saw blades).
Product Familiarisation
Summary of Contents for 953452
