6
GB
Unpacking and Assembling your
Hot Air Gun
Carefully unpack and inspect the hot air gun. Fully familiarise yourself
•
with all features and functions of the tool.
If any parts are damaged or missing, have these parts repaired or
•
replaced before use.
Fitting Accessories
NOTE:
Always ensure that the hot air gun is unplugged, and fully cooled
before attempting to fit accessories.
The accessory nozzles (4) supplied, allow the hot air gun to be used for a
•
variety of different tasks.
Accessories are a push fit onto the outlet nozzle (1).
•
Operating Instructions
Always hold the machine by the handle provided.
•
Do not obscure the inlet vents (2).
•
Always wear appropriate personal protective equipment for the job that
•
you are to do. Use of this machine requires ear defenders, safety goggles,
gloves, and a breathing mask.
Switching on
The outlet has two preset temperatures. This can be adjusted by
•
changing the position of the on/off switch (3).
For the lower setting (300ºC) move the switch into the “I” position.
•
For the higher setting (600ºC) move the switch into the “II” position.
•
To turn the hot air gun off move the on/off switch to the “O” position.
•
Be aware that the metal parts of the tool will remain hot for some time
•
after switching off. Allow at least 30mins for the gun to cool before
leaving unattended.
Paint stripping
Connect the tool to the mains supply, and switch on.
•
Direct the hot air onto the paint to be removed, keeping the nozzle at
•
least 25mm away from the surface.
NOTE: Take extra care when removing paint from window frames.
The heat from this tool can cause damage to glass if used carelessly.
Allow the paint to soften, and remove using a suitable scraper.
•
Do not overheat the paint, if you notice smoke or blackening, stop
•
heating.
Do not allow waste to build up, or drop into the outlet nozzle (1) as it will
•
be a fire hazard.
Pipe defrosting
This hot air gun can be used to defrost frozen water pipes.
•
Using a suitable attachment, aim hot air at the frozen pipe. Move the hot
•
air gun along the pipe so that the whole length defrosts evenly.
Be aware of overheating areas directly behind the pipe being defrosted.
•
Do not attempt to defrost PVC pipe as the heat of the air may cause
•
permanent damage.
Drying
This hot air gun can be used to dry damp wood or other materials.
•
Be very careful when operating power tools near damp materials, the
•
presence of water greatly increases the danger of electric shock.
Always refer to the product manufacturers instructions if using the hot
•
air gun to dry plaster, paint, or other finishes. Do not use the hot air gun
on any flammable material, or any material than may produce hazardous
fumes.
Stationary use
This hot air gun can also be used statically, keeping hands free to
•
manipulate the workpiece.
The hot air gun is designed to stand upright on a suitable workbench.
•
The outlet nozzle (1) should point straight upwards. The nozzle must not
contact the workbench, or any other object.
Ensure that the power cable is well supported, and will not become
•
caught as you work.
Switch the hot air gun on, and move workpiece into the hot air flow. Take
•
care to keep your hands and face away from the hot air.
Maintenance
Cleaning
Disconnect the machine from the mains supply before cleaning.
•
Keep your machine clean. Always clean dust and particles away, and
•
never allow ventilation holes to become blocked. Do not allow waste to
collect on any part of the tool. Use a soft brush, or dry cloth to clean the
machine, if available blow through the ventilation holes with clean, dry,
compressed air.
Disposal
Do not dispose of power tools, or other waste electrical and electronic
•
equipment, with household waste.
Contact your local waste disposal authority for information on the proper
•
way to dispose of tools.
1
Outlet nozzle
2
Inlet vents
3
On/Off switch
4
Accessory nozzles
Product Familiarisation
PDF Compressor Pro
Summary of Contents for 127655
Page 3: ...2 4 1 3 2 ...