8
GB
7. Press the button
|
2
. The red LED
|
1
lights up. The film is being sealed.
- After approx. 5 - 7 seconds, the red
LED
|
1
goes out and the sealing pro-
cess is completed.
8. Simultaneously, press buttons
|
8
in order
to release the lock of the lid
|
11
.
9. Open the lid
|
11
and remove the bag.
10. Check the welding seam. It should be a
smooth creaseless seam.
8.3
Vacuum-pack and seal
the bag
DANGER! Risk of electric
shock due to moisture!
~
For vacuum packing, no liquids must be
inside the bag.
~
Ensure that no liquid is sucked in during
the extraction of air. If this occurs, interrupt
the process by pressing the button
|
3
.
1. Smooth the bag where it is to be
sealed.
2. Open the lid
|
11
.
3.
Figure A:
place the bag in the device.
For this purpose, the end of the film
must be positioned shortly in front of the
rear limitation webs
|
12
and the lateral
limitation webs
|
15
.
4. Ensure again that there are no creases
in the film - especially in the area above
the welding wire
|
14
.
5. Close the lid
|
11
.
6.
Figure B:
use both hands to press firm-
ly on the edges of the lid
|
11
. They must
engage audibly.
7. Press the button
|
4
. The green LED
|
5
lights up. The vacuuming starts.
- After the vacuuming, the green LED
|
5
goes out and the red LED
|
1
lights up -
the sealing process is active. After ap-
prox. 5 - 7 seconds, the red LED
|
1
goes out and the sealing process is
completed.
8. Simultaneously, press buttons
|
8
in order
to release the lock of the lid
|
11
.
9. Open the lid
|
11
and remove the bag.
10. Check the welding seam. It should be a
smooth creaseless seam.
9. Cleaning and
storage
DANGER! Risk of injury
through burning/scalding!
~
Allow the device to cool down com-
pletely before you clean it or put it
away.
~
The welding wire
|
14
becomes very hot
during operation. Do not touch the hot
welding wire
|
14
.
DANGER! Risk of electric
shock!
~
Prior to cleaning, disconnect the mains
plug
|
6
of the device.
DANGER! Risk of electric
shock due to moisture!
~
The device, the power cable
|
6
and the
mains plug must not be immersed in
water or any other liquids.
WARNING! Risk of material
damage!
~
Do not use any astringent or abrasive
cleaning agents.
9.1
Cleaning
In order to ensure the proper function and
the full capacity of your device, clean it reg-
ularly.
•
Wipe down the housing of the device
with a damp cloth.
•
Prior to the next use, the device must be
completely dry.
__CPE281169_Folienschweissgeraet_B4.book Seite 8 Montag, 19. September 2016 3:02 15
Summary of Contents for SFS 110 B2
