background image

 

4

 Operation

•  Use only in dry rooms.
•  The operating range of the system must remain visible during 

operation if one or more transmitters are used for controlling the 
system.

•  Keep control systems out of the reach of children and the disabled.
•  Dispose of used batteries properly.

Safety instructions for radio operation

Observe all safety instructions for radio operation.

Only use radio systems which are approved and can be operated 
without interference.
•  Radio systems must not be operated in areas where there is an 

increased risk of interference (e.g. hospitals, airports).

•  The remote control is only approved for units and systems for 

which any malfunction of the transmitter or receiver would not 
result in a risk for persons, animals or property, or if such a risk is 
covered by other safety equipment.

•  The operator has no protection whatsoever against interference 

by other telecommunication installations and local terminals (e.g. 
also from radio installations which are operated properly in the 
same frequency range).

•  The range of the radio signal is limited by legislation and the 

structural conditions.

Intended use

          The SG 10302 hand-held radio transmitter is a multi-channel 
transmitter. It can be used unidirectionally or bidirectionally. 
The hand-held transmitter must only be used for the control 
of Silent Gliss shading systems which are equipped with the 

Safety instructions for radio operation

Summary of Contents for SG 10302



















Reviews: