background image

 17

Cleaning

Clean the unit with a damp cloth. Do not use a detergent. This may 
attack the plastic.

Disposal

After the end of its service life, dispose of the unit in accordance 
with the relevant regulations.

Troubleshooting

Fault

Cause

Remedy

 System does not run, 
status display does 
not light

1. Batteries are low
2. Batteries are incor-
rectly installed

1. Insert new batteries
2. Insert batteries 
correctly

 System does not run, 
status display lights 
red or 

fl

 ashes orange

Unidirectional: Status 
display lights green

1. The receiver is 
outside the transmit-
ting range.
2. Receiver out of 
order or faulty
3. Receiver not yet 
programmed

1. Reduce distance to 
the receiver
2. Switch on or 
replace receiver
3. Program receiver

 System operates in 
the wrong direction

Directions are incor-
rectly allocated

Delete transmitter and 
reprogram

 Required system 
does not run

Incorrect channel 
selected

Select correct channel

Repair

Please contact your dealer if you have any questions.
Please always provide the following information:
•  Item number and name on the type plate
•  Type of fault
•  Unusual events occurring prior to fault
• Accompanying conditions
• Own suspicion

Cleaning

Summary of Contents for SG 10302



















Reviews: