background image

5-Pin Power

Harness*

7921P

Controller

Shock Sensor

(White 4-Pin Socket****) 

Programmable Key Receptacle

for Changing to

Customer Mode

or

Putting Unit to Sleep Mode

Supplied with 5901H1, 5901H2 or 5901H3 Harness Kits or

 

Custom Starter/Disable T-harness.

**  

Supplied with 5902 Ignition Controlled Locking Kit.

*** 

Supplied with ALA-RPS, ALA-RPS2 or ALA-RPS3 relay packs.

****  For a Single-Zone Shock Sensor use ALA930.
 

For a Dual-Zone Shock Sensor use ALA95 or ALA90.

*****  This wire su12V power, if not used cut this wire
 

off at connector to prevent shorting.

Pink Wire Parking Lights Relay Input

Red/White Wire Parking Lights Relay Output

Violet Wire Positive Door Trigger Input

White/Black Wire Channel #2 Output

Green Wire Negative Door Trigger Input

Blue Wire Negative Pin Trigger Input 

Brown Wire 

Positive (+) Output for 

an Optional Electronic Siren

Blue/White Wire (-) Signal Output to

Disarm Factory Alarm

Gray Wire Horn (-) Pulsed Output

Starter Disable 

Socket*

Driver's Door

Lock

Unlock

Factory Keyless

Module

(Typical)

Left Door 

Lock/Unlock Switch

Lock

Unlock

Right Door 

Lock/Unlock Switch

Left Door

Jamb

Right Door 

Jamb

Lock (+)

Unlock (+)

Lock (+)

Unlock (+)

Right Front
Pass. Door

Left Rear
Pass. Door

Lock (+)

Unlock (+)

Right Rear
Pass. Door

Lock (+)

Unlock (+)

B

C

A

C

A

C

A

= Possible Connection Points for Green Wire

B

= Connection Point for Blue Wire

= Possible Connection Points for White Wire

Inside Door

Inside Door

Inside Vehicle

Green Wire

White Wire

Blue Wire

B

lack Wire

 (Unlock)

Re

d

 Wire

 (Lock)

O

ran

ge Wire

  ***** 

2nd Unlock Outp

ut (re

q

uires

additiona

l relay 

&

 special wiring).

Optional

5902 Harness

Auxiliary Interrupt

(Orange 2-Pin Socket***) 

Programmable Key

(Green 2-Pin Socket) 

Ignition Locking**

(Black 3-Pin Socket) 

LED

(White 2-Pin

Socket) 

Valet Switch

(Blue 2-Pin Socket) 

Arm/Disarm Harness

(White 3-Pin Socket) 

DIP Switches

Proposed

© 2005 Copyright Magnadyne Corp.

INSTALLATION INSTRUCTIONS

Model: 7921P

 

Summary of Contents for 7921P










Reviews: