background image

8

05.07

 

5

            

INITIAL OPERATION

Fig. 5

Input 230 V 50/60 Hz / 44 W
Output 7.2-14.4 V      1.9 A

Fig. 6

176

177

5.1  BATTERY CHARGER

The mains supply must comply with the specifi cati-

ons on the rating plate (Fig. 5).

The battery charger is suitable only for charging 

batteries from the Bosch range of tools (NiCd/

NiMH) with voltages between 7.2 V and 14.4 V.

5.2  FIRST BATTERY CHARGE

NOTE:

Please observe the following points in order to 

ensure optimum battery life:

–  Connect battery charger (177) to mains supply.

–  Insert battery (176) into battery charger slot.

For the fi rst charge, leave the battery in the 

charger for at least fi ve hours, regardless of the 

battery indicator 

(the charging time for all subse-

quent charges is about 60 minutes).

For all subsequent charges, only recharge the 

battery when the LED indicator on the tool indi-

cates battery empty (see Chapter 6.3). Avoid 

charging when the battery is not yet dischar-

ged. This will ensure optimum battery capacity 

and life.

Maximum battery output will be reached after four 

or fi ve charging/discharging cycles.

5.3  CHARGING THE BATTERY

The charging process and error functions are indi-

cated by a green light (see chapter 4.4).

The charging time is approximately 60 minutes. 

The maximum charging current fl ows when the 

tem-perature of the battery is between 15–40°C. 

Avoid charging the battery at temperatures below 

0°C and above 40°C.

NOTE:

If the battery is not to be used for a longer 

period (several days), it should be removed 

from the tool and charged/stored in the battery 

charger.

The intelligent charger with fuzzy control charges 

the battery with the optimum rapid charging current, 

depending on temperature and capacity. If fully 

charged, a preserving charge will prevent selfdi-

scharge and thus guarantee a long battery life.

Green LED

BUY AT ALLSTRAP (866) 779-2673 

Summary of Contents for BXT 10




















Reviews: