background image

5

05.07

Original spare parts must be 

used exclusively! 

Not using original spare parts 

will dissolve the warranty and 

the liability.

Use for the intended purpose

This tool is designed for strapping packages, pallet 

loads and the like.

The tool was designed and manufactured to provi-

de safe handling during the strapping operation.

The tool is designed for use with plastic straps 

(polypropylene and polyester).

Possible misuse

The use of steel straps is not possible.

3.1  SAFETY INSTRUCTIONS FOR

    BATTERY CHARGER AND BATTERY

              Always inspect the electrical plug

   

 

and cable before use. If damaged, 

              they must be replaced by qualifi ed

   

 

personnel.

•  Do not charge other types of batteries (see    

  chapter 5.1) and use original accessories only.

•  Keep the battery charger slot free of foreign    

  objects and protect against dirt.

•  Protect the battery charger against humidity and  

  use it in dry areas only.

•  Do not open the battery. Protect the battery    

  against impact, heat and fi re. Risk of explosion!

•  When the battery is outside the battery charger,  

  cover its battery terminals to avoid short circuits  

  with metal objects. Risk of fi re and explosion!

•  Keep battery dry and protected against frost. Do  

  not store it at temperatures over 50°C (122°F) or

  below 10°C (50°F).

•  Damaged batteries should not be used longer.

 

3

 

                                       SAFETY INSTRUCTIONS

Inform yourself!

Read the operating instructions 

carefully.

Preventive and corrective main-

tenance on the tool may only be 

carried out by trained personnel.

Protect yourself!

When operating the tool, wear 

eye, face and hand protection 

(cut-proof gloves).

Power source!

Before starting preventive or 

corrective maintenance, remove 

battery from the tool.

Warning: 

Strap will snap forward!

When cutting the strap, hold the 

upper portion and stand safely 

away from the strap.

Caution:

 

The lower strap will snap 

forward.

Warning: 

Strap could break!

Do not stand in line with the strap 

while it is tensioned. The strap 

could break!

Caution: 

Only strap packed goods!

Do not put hands or other parts of 

the body between the strap and 

the package during the strapping 

process.

Caution:

Danger of squeezing!

Do not put your fi ngers into the 

tension wheel area.

Do not use water!

Do not use water or steam to 

clean the tool.

WARNING

BUY AT ALLSTRAP (866) 779-2673 

Summary of Contents for BXT 10




















Reviews: