![background image](http://html1.mh-extra.com/html/sigma/2-6/2-6_operating-manual_1267893036.webp)
Laboratory Centrifuge Sigma 2-6
6 Using the centrifuge
36
Version 04/2007, Rev. 2.10 of 06/11/2015 • sb
Translation of the original operating manual, part no. 07044
Pos: 137 /10 0 Sigm a/10 0 BA Z entrif uge n Sigm a (Sta nda rd mod ule)/ 062 B etrie b_Spinc ont rol Easy +Unive rsal/Spi ncont rol Easy 062 -00 30- 003 0 Pro gra mm @ 2 8\mo d_1 405 320 480 297 _68. docx @ 19 434 1 @ 3 @ 1
6.3.3 Programs
The program is used to save or load certain recurrent settings of the
centrifuge. 10 different programs (0-9) can be saved and called up. This is
only possible at a standstill.
Pos: 138 /01 0 Univ ersal mod ule/L eerz eile @ 0\m od_ 120 211 624 450 0_0. docx @ 11 4 @ @ 1
Pos: 139 /10 0 Sigm a/10 0 BA Z entrif uge n Sigm a (Sta nda rd mod ule)/ 062 B etrie b_Spinc ont rol Easy +Unive rsal/Spi ncont rol Easy 062 -00 30- 003 0-0 010 Aktu elle Einstell ung en sp eiche rn @ 28\ mo d_14 053 204 811 99_ 68.d ocx @ 194 355 @ 4 @ 1
6.3.3.1 Saving the current settings
• Turn the left function knob until "save" is indicated and confirm the
selection by pressing the right function knob. The indication "save"
flashes and the modification mode is active.
• Select the desired program number by turning the right function knob
and confirm the selection by pressing the right function knob.
NOTE
Program numbers that are already occupied will be overwritten with the
current data.
Fig. 16: Saving a program; here: program no. 8
Pos: 140 /01 0 Univ ersal mod ule/L eerz eile @ 0\m od_ 120 211 624 450 0_0. docx @ 11 4 @ @ 1
Pos: 141 /10 0 Sigm a/10 0 BA Z entrif uge n Sigm a (Sta nda rd mod ule)/ 062 B etrie b_Spinc ont rol Easy +Unive rsal/Spi ncont rol Easy 062 -00 30- 003 0-0 020 Ges peich ert e Pro gra mm e ab ruf en @ 28\ mod _14 0532 048 215 7_6 8.do cx @ 1 943 69 @ 4 @ 1
6.3.3.2 Calling up stored programs
• Turn the left function knob until "run" is indicated and confirm the
selection by pressing the right function knob. The indication "run"
flashes and the modification mode is active.
• Select the desired program number by turning the right function knob
and confirm the selection by pressing the right function knob.
The program is now loaded.
Fig. 17: Loading a program; here: program no. 8
Pos: 142 /01 0 Univ ersal mod ule/L eerz eile @ 0\m od_ 120 211 624 450 0_0. docx @ 11 4 @ @ 1
Pos: 143 /10 0 Sigm a/10 0 BA Z entrif uge n Sigm a (Sta nda rd mod ule)/ 062 B etrie b_Spinc ont rol Easy +Unive rsal0 62- 004 0 Aussc halte n @ 28\ mod _14 0532 042 357 1_6 8.do cx @ 1 941 31 @ 2 @ 1
6.4 Switching the centrifuge off
• Open the centrifuge when it is not in use so moisture can evaporate.
• Switch the centrifuge off by pressing the mains power switch.
Pos: 144 /01 0 Univ ersal mod ule/Absc hnittsw echsel @ 0\ mod _12 021 245 140 62_ 0.docx @ 4 18 @ @ 1
Pos: 145 /01 0 Univ ersal mod ule/Seit enwec hsel @ 0\m od_ 120 211 624 4312 _0. docx @ 10 5 @ @ 1