manualshive.com logo in svg

SIGLENT SDS1000CML+, User Manual, Page: 145 / 159

Share
Download
SIGLENT SDS1000CML+ User Manual Download Page 145

                                                                                     

SIGLENT                                 

SDS/SD Quick Start    11 

Function Introduction of Front Panel   

 

Vertical Control 

 

 

 

:

 

Input channels. These two channels are marked with 

different  colors  to  distinguish  different  input  channels  and  their 

waveforms.  Pressing  the  channel  button  will  turn  on  the 

corresponding  channel  as  well  as  its  menu,  and  pressing  it  twice 

continuously will turn off the channel. 

 

: 

Press  the  button  to  enable  math  function  which  includes 

five operations: adding, subtracting, multiplying, dividing and FFT. 

 

 

: 

Press the button to enable the reference waveform function. 

By  recalling  the  previously  saved  waveform,  we  could  compare  it 

with the current waveform to decide circuit failures.

 

 

:

 

Modify  vertical  position  of  the  current  waveform.  Turn 

clockwise  to  increase  the  position  while  turn  counterclockwise  to 

decrease it. The  waveform  will move up or down  and the  position 

message  at  the  lower-left  corner  of  the  screen  will  change  along. 

Press down the knob to quickly reset the vertical position to zero.

 

 
 
 
 

 

Math 

Ref 

2 

1 

Summary of Contents for SDS1000CML+
































































































































































Reviews:

No comments