manualshive.com logo in svg

SIGLENT SDS1000CML+, User Manual, Page: 117 / 159

Share
Download
SIGLENT SDS1000CML+ User Manual Download Page 117

SIGLENT 

SDS/SD    User  Manual   

107

 

2.14 Online Help Function 

The  oscilloscope  has  an  online  help  function  that  supplies  multi-language  help 

information, and  you  can recall  them  to  help you  operate  the  oscilloscope  when 

you need. 

Press the “HELP” button to enter the help status, then press every button to recall 

the corresponding help information. Note

：

If you want to see help information of 

SINGLE button and RUN/STOP button, you need to see them when you first enter 

the help status because you press the SINGLE button can enter next page of help 

information and Press the RUN/STOP button can return to the first page of help 

information when other button’s help information exceed one page.   

All submenus of every main menu have their help information. Note: If you want to 

see help information of next page submenus, first you need to press the “HELP” 

button to exit the help status and switch to next page menu then press the “HELP” 

knob to enter the help status again and press the submenu option buttons to see 

its help information.

 

 

 

Picture 2.14-1 

 

 

 

 

Summary of Contents for SDS1000CML+
































































































































































Reviews:

No comments