manualshive.com logo in svg

SIG Wonder, Building And Flying Instructions, Page: 4 / 24

Share
Download
SIG Wonder Building And Flying Instructions Download Page 4

. 

ABOUT THE BUILDING SEQUENCE

 
The quickest and most efficient way to complete a model is to work on several pieces at the same time. While the glue is drying 
on one section, you can start on or proceed with another part. Keep in mind that the number sequence used in these 
instructions was chosen as the best way to explain the building of each major component and is not intended to be followed 
exact one-two-three fashion. Start on the wing at No.1 and after doing as many steps as is convenient, flip over to "Fuselage 
construction" an do a step or two or three, then back to "Wing Construction" and so forth. You will arrive at points where you can 
go no farther until another component is available. 
 
Plan ahead! Read the instructions completely and study the full size plans before beginning construction.
 

COMPLETE KIT PARTS LIST

Die-Cut Balsa

4 1/16"x3"x18" Wing Ribs

2 3/32"x4"x18" Fuselage Side, 

Fuselage Doubler

1 1/8"x4"x18" fins, Wing Block 

Pads (WBP)

Printed Balsa

1 1/4"x2"x12" Canopy, Wing Dowel 

Supports (WDS)

Sheet Balsa

2 1/16"x1"x36" Trailing Edge 

Sheeting

1 1/16"x3"x18" Wing Center 

Sheeting

2 1/16"x3"x36" Leading Edge 

Sheeting

1 1/8"x3"x18" Fuselage Bottom

2 1/8"x4"x10" Sheets for Optional 

Fins

2 3/16"x4"x12" Stabilizer and 

Elevator

2 1/4"x3"x3" Fuselage Top, 

Cowl Bottom

Stick Balsa

3 1/16"x1/4"x36" Capstrips

1 1/4"x1/4"x36" Leading Edge

5 1/4" Traingle x12" Corner 

Braces, Skid Sides

1 1/2" Triangle x6" Cowl Filler

Block Balsa

2 1"x1-1/2"x9" Wingtips

Special Cut Balsa

1 3/16"x3/8"x36" Tapered Trailing 

Edge

2 3/16"x1-1/4"x12" Tapered Ailerons 4 3/16"x1"x3" Cowl Sides

Pre-Cut Plywood

1 3/32"x2-3/4"x6" Birch Ply F-1, 

Aileron Servo Mounts (ASM)

1 1/8"x2-3/4"x9" Lite-Ply Formers, 

HP, Hatch Lip, Spinner Ring

Sawn Plywood

1 1/16"x7/8"x2-1/2" Birch Ply Wing 

Hold-Down Plate

Hardwood

1 1/8"x1/8"x9" Spruce Fin Stiffener

2 1/8"x1/4"x36" Spruce Wing Spars

1 1/8"x5/16"x12" Spruce Skid

2 3/16" dia. x1-1/2" Birch Wing 

Dowels

2 1/4"x1/2"x1-1/2" Basswood Wing 

Hold-Down Blocks

Formed Wire Parts

1 4-40x8" L.H. Aileron Torque Rod 

(with brass bearing)

1 4-40x8" R.H. Aileron Torque Rod 

(with brass bearing)

Miscellaneous

1 4"x20" Decal DKM-266A (for 

Standard Version)

1 4"x20" Decal DKM-266B (for 

Russian Version)

1 4"x20" Decal DKM-266C (for 

Angel Version)

1 4"x20" Decal DKM-266D (for 

Patriot Version)

1 38"x50" Full-Size Printed Plan

1 20 pg. Photo Illustrated Instruction 

Book

Hardware

2 Small Glass-Filled Engine Mounts

2 #2x3/8" Flat Head Wood Screws 

(for hatch)

2 #2x1/2" Sheet Metal Screws 

(for control horn)

4 6-32x5/8" Socket Head Mounting 

Blocks (for engine mounts)

2 10-32x1" Nylon Wing Bolts

4 6-32 Blind Nuts (for engine 

mounts)

1 2-56 Solder Link (for 

throttle)

3 2-56 Nylon RC Links (2/aileron, 

1/elevator)

3 2-56x10" Threaded Rods 

(2/aileron, 1/elevator)

2 4-40 Nylon Aileron Connectors

1 Nylon Control Horn (for 

elevator)

1 130" o.d.x12" Nylon Tubing (for 

throttle pushrod)

1 1/16" dia.x12" Steel Cable (for 

throttle pushrod) 

7 3/4"x1" Easy Hinges

1 Pushrod Connector Package

Summary of Contents for Wonder

























Reviews:

No comments