SIG Wonder Building And Flying Instructions Download Page 24 | Manualshive

Page: 24 / 24

SIG Wonder Building And Flying Instructions Download Page 24

.

WARNING - DANGER Important! Read these Warnings:

A model airplane motor gets very hot and can cause serious burns. Do not touch the motor during
or after operation. Keep clear of the propeller, it can cut off a finger or put out an eye. Make sure
the propeller is securely fastened in place and is not cracked. Model airplane fuel is flammable and
poisonous. Take the same precautions while transporting and using it that you would with a can of
gasoline or a bottle of poison.
Remember that it is possible to lose control of a model airplane. Do not fly in locations where the
model may hit people or damage property if loss of control occurs. Check your model and
equipment regularly to insure it is in safe operating condition.

© Copyright SIG Mfg. Co., Inc.

SIG MFG. CO., INC............Montezuma, Iowa 50171-0520

LIMIT OF LIABILITY:

In use of our products, Sig Mfg. Co.'s only obligation shall be to replace such quantity of the product proven to be defective.
User shall determine the suitability of the product for his or her intended use and shall assume all risk and liability in connection
therewith.

«
...
22
23
24

Summary of Contents for Wonder

























Reviews:

No comments