manualshive.com logo in svg

SIG Wonder, Building And Flying Instructions, Page: 21 / 24

Share
Download
SIG Wonder Building And Flying Instructions Download Page 21

. 

"ANGEL" VERSION

 

 
The Navy's flight demonstration team, 
the Blue Angels, was the obvious 
inspiration for this Wonder version. Even 
though it's not jet-powered, the Angel 
Wonder can do a pretty impressive 
aerobatic routine itself! The big canopy 
on the Angel is easier to install than the 
others because it doesn't have to match 
up with another piece glued to the 
stabilizer. You might also notice that the 
very aft end of the fuselage is cut off at 
and angle to match the fins - it just 
seemed to look better that way!

 

 

Covering the "Angel"

 
The Angel is the simplest Wonder to cover because it's basically all one color. 
The top of the plane is distinguished with some large decals and bright yellow 
stripes. To duplicate the Angel color scheme, you'll need the following materials: 

Dark Blue Supercoat Covering

- Entire airframe.  

Cub Yellow Supercoat Covering

- Wing tips, fin tips.  

Silver Supercoat Covering

- Canopy.  

Cub Yellow SuperTrim

- Stripes on top of wing and stabilizer.  

Silver SuperTrim

- Wing and fin leading edges.  

Decal Sheet

- SIGDKM266C  

 

 
Cover the wingtips and fin tips with yellow first, then cover the rest of the airframe with dark blue. The yellow stripes should 
be cut in one piece, applied to the assembled airplane, then cut at the junction of the wing and stabilizer. The silver leading 
edges are 1"x16-1/2" strips of trim material. Center the strips on the leading edge so that there is an equal amount on the 
top and bottom wing surface. The outboard end of the silver stripes should end at the yellow wingtip. The silver leading 
edge pieces for the fins are cut from trim material using the pattern shown on the plan.

 

Engine Installation

 
The ASP .12 engine that's bolted to the 
front of the Angel is a true winner. It's 
powerful, idles well, and is very 
economical on fuel. We used a two 
ounce tank in our prototype, and still 
had more flight duration than we really 
needed. The performance with this size 
of engine is still pretty hot, you just can't 
go up, up out of sight.

 

 

 

Radio Installation

 
Again the Futaba R114H receiver was installed in the F-3 opening. The 250 maH battery on this particular model needed to 
be located at the aft end of the wing opening, just ahead of F-4. It's held in position with some scrap pieces of balsa which 
can be broken away easily when the time comes to remove the battery. 
 
There was still plenty of room left between the receiver and battery for the throttle servo to be taped in place. The elevator 
servo was mounted in its familiar position behind F-4. We used three Futaba S133 micro servos in this prototype. The 
weight savings of three micro servos over standard servos is nearly 3 ounces. That's a lot for a model of this size!

Summary of Contents for Wonder

























Reviews:

No comments