background image

 Instruction Manual

Model 4105 Gas Sensor Module (12/02)

Page:  13

10. LIMITED WARRANTY

SIERRA MONITOR CORPORATION warrants its products
to be free from defects in workmanship or material under
normal use and service for two years after date of shipment.
SMC will repair or replace without charge any equipment
found to be defective during the warranty period.  Final
determination of the nature and responsibility for defective
or damaged equipment will be made by SMC personnel.

All warranties hereunder are contingent upon proper use in
the application for which the product was intended and do
not cover products which have been modified or repaired
without SMC approval or which have been subjected to
accident, improper maintenance, installation or application,
or on which original  identification marks have been removed
or altered.  This Limited Warranty also will not apply to
interconnecting cables or wires, consumables (ie. calibra-
tion gases, batteries, sensors), nor to any damage resulting
from battery leakage.

In all cases SMC’s responsibility and liability under this
warranty shall be limited to the cost of the equipment.  The
purchaser must obtain shipping instructions for the prepaid
return of any item under this warranty provision and compli-
ance with such instruction shall be a condition of this war-
ranty.

Except for the express warranty stated above, SMC disclaims
all warranties with regard to the products sold hereunder
including all implied warranties of merchantability and fit-
ness and the express warranties stated herein are in lieu of
all obligations or liabilities on the part of SMC for damages
including, but not limited to, consequential damages arising
out of/or in connection with the use or performance of the
product.

9.

REPLACEMENT PARTS

4205-02

Sensor Assembly, Combustible, Non-Intrusive

4205-03

Sensor Assembly, 4-20 mA O2, Non-Intrusive

4207-04

Sensor Assembly, 4-20 mA CO, Non-Intrusive

4205-05

Sensor Assembly, 4-20 mA H2S, Non-Intrusive

4205-06

Sensor Assembly, 4-20 mA Cl2, Non-Intrusive

4207-07

Sensor Assembly, 4-20 mA H2, Non-Intrusive

4207-10

Sensor Assembly, 4-20 mA SO2, Non-Intrusive

4207-12

Sensor Assembly, 4-20 mA NO2, Non-Intrusive

4207-21

Sensor Assembly, 4-20 mA HCl, Non-Intrusive

4207-22

Sensor Assembly, 4-20 mA HCN, Non-Intrusive

4207-25

Sensor Assembly, 4-20 mA NH3, Non-Intrusive

4207-26

Sensor Assembly, 4-20 mA HF, Non-Intrusive

5311-00

Rainshield

Summary of Contents for 4105 SERIES Applicability & effectivity




















Reviews:

Related manuals for 4105 SERIES Applicability & effectivity