Siemens VersiCharge Ultra 50 Installation Manual Download Page 20 | Manualshive

Page: 20 / 28

background image

Underground conduit and wiring

The Ultra 50 is supplied with a Flexa conduit system in the crate
kit, with all parts attached.

1. Disassemble the Flexa system

Detach all pieces of the system below the conduit. The flex
adapter is removed by pushing in the adapter ring, and pulling
out the conduit.

2. Fit Flexa system into base

Install the 6” conduit nipple, conduit coupling and flex adapter
into the embedded 6” coupling (not supplied) in the
foundation, using sealant on all threads.

6” conduit

nipple

conduit

coupling

flex

adapter

flexa

conduit

flex

adapter

washer

locking

ring

Push in ring

Pull out conduit

VersiCharge Ultra 50™ |

Installation Manual

20

«
...
18
19
20
21
22
...
»

Summary of Contents for VersiCharge Ultra 50





























Reviews:

No comments

Related manuals for VersiCharge Ultra 50

Brand: Quick Charge Pages: 4

Brand: Daewoo Pages: 7

Brand: AlzaPower Pages: 50

Brand: AML Pages: 2

Brand: Analytic Systems Pages: 12

Brand: Toa Pages: 8

Brand: Aegis Pages: 2

PROFI POWER 2.913.914

Brand: axhess Pages: 27

Brand: Turnigy Pages: 24

Brand: Kompernass Pages: 10

Brand: Skyrc Pages: 17

Brand: Icy Box Pages: 12

Brand: Yamaha Pages: 129

Brand: LG Chem Pages: 4

Brand: HOTA Pages: 34

Brand: Bossard Pages: 16

Brand: chinavasion Pages: 2

77 02 8 551 896

Brand: BMW Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands