manualshive.com logo in svg

Siemens VersiCharge Ultra 50, Installation Manual

Share
Download
Siemens VersiCharge Ultra 50 Installation Manual Download Page 18

Installation

1.  Secure to foundation

Lift the Ultra 50 by the supplied lifting straps, place onto the 
prepared foundation and secure with the specified fasteners.   

Note

: Use the plastic inserts you kept earlier in the baseplate 

holes.

 

2. Remove fasteners from front panel

Remove the 6x security screws and washers from the front 
panel using the provided 5mm pin hex tool.

3. Place front panel on ground

The front panel is attached to the enclosure with wiring and an 
earthing strap on the front left-hand side.

Lift the front panel up to release from the top hook and gently 
lower to the ground in front of the Ultra 50. 

In calm conditions, it may be possible to keep the front panel 
connected during commissioning.  If this is possible, go to page 
17, item 5.

If in doubt, disconnect the front panel (see pg 17, item 4) and 
store in a safe place until the unit is ready to close for use.

VersiCharge Ultra 50™ | 

Installation Manual

18

Summary of Contents for VersiCharge Ultra 50





























Reviews:

No comments

Brands by name

Popular brands

Load more brands