Siemens TEL50.GSM General Instructions Manual Download Page 5 | Manualshive

Page: 5 / 28

background image

Building Technologies

- 3 -

TEL50.GSM

1.4 Warranty

This product is guaranteed against any material and manufacture defects. SIEMENS reserves the right, at its own discretion, to
repair or replace faulty products. The warranty is deemed null and void if the fault is caused by improper use or by an operating
procedure that is not included in this manual.

The warranty will not cover faults caused by:

• improper and careless use
• damage caused by atmospheric agents
• acts of vandalism
• material that is subject to wear and tear

1.5 Contents of sales pack

• User Manual (this manual)
• TEL50.GSM device
• 230VAC / 12VDC 1A power supply
• GSM stilo antenna

«
...
3
4
5
6
7
...
»

Summary of Contents for TEL50.GSM





























Reviews:

No comments

Related manuals for TEL50.GSM

vlt soft starter mcd 500

Brand: Danfoss Pages: 95

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 33

Brand: Danfoss Pages: 59

Brand: Danfoss Pages: 16

VLT AQUA Drive FC 200

Brand: Danfoss Pages: 91

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 100

Brand: Danfoss Pages: 82

Brand: Danfoss Pages: 18

Brand: Danfoss Pages: 12

OPTYMA Plus OP-LPQM

Brand: Danfoss Pages: 8

Brand: Watts Pages: 12

Brand: Lancom Pages: 8

Brand: Nice Pages: 120

Dual Motor Focus Controller

Brand: Pegasus Astro Pages: 16

Brand: DAY Pages: 23

Lift Inverter L1000V

Brand: YASKAWA Pages: 282

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands