background image

 

 

 

Building Technologies  

- 22 - 

TEL50.GSM 

 

 

7.3  Alarm notification enabling 

The TEL50.GSM can handle the following alarms: 

Contact IN1 closed alarm 

Temperature threshold exceeded alarm 

7.3.1 IN1 

closed 

alarm 

This alarm may come from any device whose status needs to be monitored (eg. home alarm system, boiler burner block, etc.). 
A potential-free contact must be used. When the contact is closed, an SMS is sent to all the users on the USER list (both fixed 
and mobile numbers). The text of the message will contain “ALARM IN1” or ALARM followed by a new identification string for 
the IN1 input if it has been changed. 

 

 

7.3.2 Temperature 

alarm 

This alarm can only be generated if the temperature sensor LG-Ni1000 is correctly connected to the respective input. The alarm 
and reset values must be set according to a hysteresis cycle. The values themselves will define the alarm activation logic. If the 
ALARM value is greater than the RESET

 

value, the alarm will be triggered if the current value is higher than the alarm value. 

Consequently, the alarm will stop if the current value is lower than the reset value. If the 

ALARM 

value is lower than the 

RESET 

value, operating will be reversed. The factory settings are ALARM=5°C and RESET=6°C (frost protection). The user can modify 
the alarm and reset thresholds as shown in the examples below.

 

When an alarm is triggered, an SMS is sent to all the users on the USER list (both fixed and mobile numbers). The text of the 
message will contain ALARM TEMP or ALARM followed by a new identification string for the ANALOG/TEMP analogue input if 
it has been changed.

 

Summary of Contents for TEL50.GSM





























Reviews: