background image

 

 

 

Building Technologies  

TEL50.GSM 

 

 

en 

English 

1.

 

I

NTRODUCTION

...........................................................1

 

1.1

 

Copyright ................................................................1

 

1.2

 

Trademarks ............................................................1

 

1.3

 

Declaration of conformity........................................2

 

1.4

 

Warranty.................................................................3

 

1.5

 

Contents of sales pack ...........................................3

 

2.

 

I

NSTRUCTIONS

............................................................4

 

2.1

 

Safety instructions ..................................................4

 

2.2

 

Operating instructions ............................................6

 

3.

 

G

ENERAL INFORMATION

..............................................7

 

4.

 

I

NSTALLATION

.............................................................8

 

4.1

 

Wall-mounting ........................................................8

 

4.2

 

Electrical connections.............................................8

 

4.3

 

Connection of stilo antenna..................................11

 

4.4

 

Connection of external antenna (optional) ...........11

 

4.5

 

Insertion of SIM card ............................................12

 

4.6

 

Checking of indicator lamps .................................13

 

5.

 

T

ECHNICAL DATA

......................................................14

 

6.

 

B

ASIC CONFIGURATION

.............................................15

 

6.1

 

Commands via DTMF tones.................................15

 

6.2

 

Commands via SMS.............................................16

 

6.3

 

Temperature sensor querying ..............................17

 

7.

 

E

XTENDED CONFIGURATION

......................................18

 

7.1

 

Creation of a qualified user list .............................18

 

7.2

 

Modification of Input-Output identification string ..20

 

7.3

 

Alarm notification enabling ...................................22

 

7.3.1

 

IN1 closed alarm....................................... 22

 

7.3.2

 

Temperature alarm ................................... 22

 

7.4

 

Digital I/O status ...................................................24

 

8.

 

E

NVIRONMENTAL COMPATIBILITY AND DISPOSAL

........25

 

9.

 

S

IGNALLING ERROR

..................................................25

 

Summary of Contents for TEL50.GSM





























Reviews: