Siemens SIPROTEC 7SS52, Operation Manual

Page: 204 / 210

'(& )( )'& &) ( &!& ")& &$(( $# Ċ %&( $# #)" &&#$
X
X - II
Siemens AG
⋅
May 1998
Installation instruction
Bay unit for panel or cubicle flush mounting, 5 - 3
Checking the connections, 5 - 8
Installation instructions, 5 - 1
Check of the nominal data, 5 - 4
Coding of the ZPS modules, 5 - 7
Connection of the bay units in the bus coupler bay, 5 - 2
Cubicle version of the master unit, 5 - 3
Installation and connection, 5 - 2
Matching of the control voltage for the binary inputs, 5 - 4
Subrack version of the master unit, 5 - 3
Version for panel surface mounting (FE, ZE), 5 - 2
Inter-changeability, 3 - 5
Isolator mimic
Bypass transfer-busbar operation, 4 - 14
Isolator treatment during auxiliary voltage supply failure,
4 - 13
Preferential treatment during busbar coupling via isolators,
4 - 13
Processing of the isolator running status, 4 - 13
Status of the feeder isolator, 4 - 17
Treament of the isolator states in the event of wire breaĆ
kage, 4 - 14
Maintenance, 7 - 1
Maintenance recommendation, 7 - 1
Marshalling possibilities, 5 - 12
Mode of operation, 4 - 1
Special treatment of the stabilizing current for the check
zone, 4 - 12
Operating instructions, 6 - 1
Operating the bay unit, 6 - 33
Keypad/display, 6 - 33
Marshalling
alarm relay - block 62, 6 - 40
binary inputs, 6 - 37
binary inputs - block 61, 6 - 37
binary outputs, 6 - 37
command relays - block 64, 6 - 43
Introduction, 6 - 37
LED indications, 6 - 37
LED indications - block 63, 6 - 41
Prerequisite and language for operation, 6 - 34
Read out of operational measured values - block 57, 6 - 46
Setting, function parameters - block 11, 6 - 44
Settings via the integrated operation - block 71, 6 - 36
Test and control function - block 40, 6 - 45
Operation of complete unit, 4 - 1
Operational control features, 6 - 20
Binary inputs, 6 - 20
Taking bays out of service - block 64, 6 - 21
Test and control functions, 6 - 21
Pre-setting, binary inputs, A - 17
Pre-settings, binary outputs, A - 17
Product description, 2 - 1
Reference table for configuration parameters, bay unit, A - 30
Repair, 8 - 1
device, 8 - 1
modules, 8 - 1
Scope of functions, 2 - 2
Busbar protection, 2 - 2
Circuit-breaker failure protection, 2 - 3
Digital inputs, trip outputs, 2 - 5
Fault recording, 2 - 5
Isolator replica, 2 - 4
Measuring and testing functions, 2 - 5
Operational and fault events, 2 - 6
re-assignable alarm relays and LED's, 2 - 5
Self-monitoring, 2 - 6
Trip output/reset, 2 - 5
Service conditions, 3 - 5
Setting the master unit, 6 - 1
Integrated keypad/display panel, 6 - 1
Confirmation keys, 6 - 2
Control keys, 6 - 2
Functions keys for text parameters, 6 - 1
Numerical keys, 6 - 1
Operating pre-requisites, 6 - 2
Setting the protection, 6 - 3
Initial displays - blocks 00 and 01, 6 - 4
Introduction, 6 - 3
Setting, overcurrent release of the TRIP command - block
65, 6 - 19
www
. ElectricalPartManuals
. com