manualshive.com logo in svg

Siemens SiPass integrated, Controller And Device Installation Manual

Share
Download
Siemens SiPass integrated Controller And Device Installation Manual Download Page 26

 

 

Access Controllers 
ACC-AP 

2 

26 | 38 

 

A6V11164550 

 

2.3.8

 

Platform Upgrade via Firmware Download 

Before attempting to perform a platform upgrade via Firmware download, ensure 

that you are using: 

●

 

Platform version V1.0.6 (or later) and 

●

 

AP Application Version V2.75.11 (or later) 

If using an earlier platform version, you must perform the platform upgrade via SD-

Card to upgrade to platform version V1.0.6 or later. The SD-Card for platform 

V1.0.6 will also contain AP application version V2.75.11. 
For more details see the 

Common Firmware Update Procedure [➙

 11] section. 

2.3.9

 

LED Indications 

2.3.9.1

 

During SD Card Update 

 

LED Indication 

Description 

RED 

–

 On 

Siemens bootstrap and u-boot running 

ORANGE 

–

 Flashing 

NAND Flash update is in progress 

GREEN 

–

 Flashing 

NAND Flash update finished, SD card shutting down 

ORANGE 

–

 On 

●

 

SD-Card shut down. Count to 7, remove power, remove SD 

card, restart. 

●

 

After SD-Card removal 

–

 ACC-Application running 

RED - Flashing 

Update failed. Retry SD-Card update 

 

2.3.9.2

 

During ACC-Application (Run-Time) 

 

LED Indication 

Description 

RED 

Controller is starting up 

ORANGE 

Application running 

GREEN 

Application running, connected with SiPass integrated 

OFF (Dark) 

Application not running. (This can occur during a Firmware 

upgrade.) 

 

 

 

Summary of Contents for SiPass integrated







































Reviews:

No comments

Brands by name

Popular brands

Load more brands